ekezz
01-02-2006, 06:47 AM
These are some questions I found at the avsim.com forum.
>1. How much would it cost me to build a DC-9 cockpit ?
>2. Where do you buy parts for these masterpieces ?
>3. How do you do it ???? I know I'm a complete noob.
>4. Does it work with FS2004 ?
>5. Do you need any special software to make it work with FS9 ?
>6. If I built a DC-9 cockpit how do I connect it to FS9 and how do I use it with FS9 ?
>7. Do I need payware DC-9 software ?? Something like the F1 Iron Knuckles DC9 ?
As I spent quite some time writing my answers, I want to share my story at IFSBI as well so other "new/potential" builders can take away what they need.
Kester
Hi,
I'll try to give a little bit of an answer. I' started about a year ago to build a 737 cocpit, so my experiences are limited...
I will give you my personal views and choices, so please first also ask other builders before you decide to spend any money.
>1. How much would it cost me to build a DC-9 cockpit ?
This depends fully on the availability of ready made DC9 components, and your ambition and your financial resources. I suspect for a DC9 you will have to construct most parts yourself or modify existing hardware. Instead of giving you a final cost estimate (if possible anyway) I would suggest that you take this as a multi year project and assign an amount of money you want to spend every year. Talking to cockpit builders who have been there a long time, they tell me it is never finished and they keep adding stuff to enhance the realism.
To give you some indication:
Software: Apart from MS-FS I purchased PMDG 737, FSUIPC and WideFS, and Project Magenta Glass Cockpit and pmSystems. This approximately adds up to Euro 800. Now for the DC9 there is no PM Glass Cockpit, but with pmSystems you can create panels yourself. For current pricing details you will have to send a mail to projectmagenta.com.
Hardware Computers: I have 5 connected, most are 4 year old PC's, except for the MS-FS computer rendering the nice graphics. I spent Euro 1250 on this and built/assembled it myself so all components are aimed at MS-FS performance as much as my budget will allow. You can see the specs at http://fly.ekezz.com
Hardware Screens: You can use CRTs, LCD's and Projectors. I am using a mix of CRT's and LCD's. For the outside view I am using two CRT's. For the Captains PFD and ND I have a LCD, for the standby instruments and upper Eicas I have a CRT. For the FMC/CDU I have a Touchscreen. For the overhead panel I presently use a laptop until the hardware wiring has been completed. The lower Eicas is not implemented yet. Using screens I already had, kept the cost down as my personal priority is on building the overhead panel and adding modules. The touchscreen was a gift from a friend who didn't use it anymore. Ever since friends and collegues hear of my project they sometimes actively offer me their old PC or screen. Now you could make a different choice here. Some builders tell me that the immersion effect is great when utilizing a projector. Others are awed by uzing multiple high res CRT's. You can buy new, you can use old. I'm waiting for a defect projector to show up and replace the defect lamp. For the FMC/CDU screen some use 7 inch LCD's. Anyway, for me it is hard to give you a cost estimate here, but if you know what your preference would be, shop around to get a price indication. And again, you can add better screens over time.
Hardware Modules: Today I have a CPflight MCP, EFIS and NAV panel ready to use, plug and play, this approximately adds up to Euro 1000. I want to add more modules so this amount will go up. It is my choice to buy ready to go modules as they are designed for the 737 and represent the real thing. It is also possible to buy modules that have a lower cost, but these don't have the look I want, this is a personal choice. The other option is to build your own panels with all kinds of components like encoders, displays, switches, etc. I have no reference to what that would cost and you need to be "tech savvy" to build it. On Ebay a friend found and purchased a real 747 Cargo panel for me as a present. I'll try to hook it up through the phidgets even though it does not belong in a 737, nice experiment.
The next level of realism is to go for very realistic look, feel and functional modules for the FMC/CDU and Throttle Quadrant. My present CH products stick and throttle are ok, but to have a real throttle quadrant with autothrottle etc is a dream, the cost... Euro 1000 and higher.
Hardware I/O: There are many types of hardware I/O boards you can hook up your switches and pot's to. All I can say is to read user experiences in various forums and builders websites. I am involved in www.ifsbi.org and you can find a forum and several links from there to cockpit builders webpages, also check out fscockpit.com.
What I did was to go for Phidgets (phidgetsusa.com) because I can assign functions from pmSystems directly to Phidgets (you do need FSUIPC and WideFS made by Pete Dowson to be found at schiratti.com).
You can also use the interface software, to be found on the phidgetsusa site. My initial Phidgets puchase of 4 boards and all kinds of leds etc set me back 400 Euro's. Then you need (rotary)switches and wiring etc. Now this can also grow over time. I have spent Euro 100 on this, but will need more as I move on to the overhead panel. And I will need more Phidgets boards. So I am expecting this to head up into the total of Euro 1000 (including money already spent).
Panels: To have the most realistic view there are some companies that make laser engraved backlit panels. The big parts are the Main Instrument Panel(s), the Overhead panel and the Pedestal. These as a total would set you back between Euro 1000-2000 and then they still need to be wired. I decided for my first year of cockpit building to go for Do-It-Yourself using MDF panels and painting it grey. At a later stage I will convert to the more high fidelity panels. There are some new vendors on the block, so I expect the prices to go down. Including the MDF casing for screens, computers etc, which I put on wheels, I spent Euro 200 so far.
Cockpit shell:
It is possible to build/order the cockpit shell. This gives an enhanced immersion effect. Can't tell you much about this, so shop around on the web.
Documentation:
There are some nice books/manuals on the working of the airplane systems, FMC/CDU, checkrides etc. When you get into programming the system logics of your aircraft, reference material is of vital importance. There is free material to be found, but some people have taken the time and effort to write very comprehensive manuals, and this is where I buy it. Total so far Euro 180.
Motion Platform:
An area that will grow in the next years as it becomes more attainable for the humble soul. Soem builders are putting their own experiment together, some vendors are exploring the possibilities as far as I know.
Well, I hope this has shed some light on your questions, in my experience this will lead to more questions. Most of the remaining questions below, I have tried to answer in the story above.
I haven't grand totalled the amount spent by me so far, as it makes no sense to do so. It is a very personal choice how much you will spend and it doesn't take into account how you spread the investment over time. All I can say, is that it is well spent because this hobby is very enjoyable and every addition, big or small brings new joy to my flight simulation experience. And I made new friends in wonderful places who share this hobby and understand what I am talking about ;-)
Happy building and see you around.
Kester Meijer
kester@ifsbi.org
>2. Where do you buy parts for these masterpieces ?
see above
>3. How do you do it ???? I know I'm a complete noob.
start small and gradually expand over time. determine which parts of simulation have priority to you. Use the categories mentioned above and put them in your preferred sequence.
>4. Does it work with FS2004 ?
Yes, I use FS2004/FS9 for the outside view and PMDG for the aircraft model, not the PMDG panels though.
>5. Do you need any special software to make it work with FS9 ?
FSUIPC is a must have and when using multiple computers add WideFS to that list. And I would add pmSystems.
>6. If I built a DC-9 cockpit how do I connect it to FS9 and how do I use it with FS9 ?
see above
>7. Do I need payware DC-9 software ?? Something like the F1 Iron Knuckles DC9 ?
I suppose so just like I did with PMDG.
>1. How much would it cost me to build a DC-9 cockpit ?
>2. Where do you buy parts for these masterpieces ?
>3. How do you do it ???? I know I'm a complete noob.
>4. Does it work with FS2004 ?
>5. Do you need any special software to make it work with FS9 ?
>6. If I built a DC-9 cockpit how do I connect it to FS9 and how do I use it with FS9 ?
>7. Do I need payware DC-9 software ?? Something like the F1 Iron Knuckles DC9 ?
As I spent quite some time writing my answers, I want to share my story at IFSBI as well so other "new/potential" builders can take away what they need.
Kester
Hi,
I'll try to give a little bit of an answer. I' started about a year ago to build a 737 cocpit, so my experiences are limited...
I will give you my personal views and choices, so please first also ask other builders before you decide to spend any money.
>1. How much would it cost me to build a DC-9 cockpit ?
This depends fully on the availability of ready made DC9 components, and your ambition and your financial resources. I suspect for a DC9 you will have to construct most parts yourself or modify existing hardware. Instead of giving you a final cost estimate (if possible anyway) I would suggest that you take this as a multi year project and assign an amount of money you want to spend every year. Talking to cockpit builders who have been there a long time, they tell me it is never finished and they keep adding stuff to enhance the realism.
To give you some indication:
Software: Apart from MS-FS I purchased PMDG 737, FSUIPC and WideFS, and Project Magenta Glass Cockpit and pmSystems. This approximately adds up to Euro 800. Now for the DC9 there is no PM Glass Cockpit, but with pmSystems you can create panels yourself. For current pricing details you will have to send a mail to projectmagenta.com.
Hardware Computers: I have 5 connected, most are 4 year old PC's, except for the MS-FS computer rendering the nice graphics. I spent Euro 1250 on this and built/assembled it myself so all components are aimed at MS-FS performance as much as my budget will allow. You can see the specs at http://fly.ekezz.com
Hardware Screens: You can use CRTs, LCD's and Projectors. I am using a mix of CRT's and LCD's. For the outside view I am using two CRT's. For the Captains PFD and ND I have a LCD, for the standby instruments and upper Eicas I have a CRT. For the FMC/CDU I have a Touchscreen. For the overhead panel I presently use a laptop until the hardware wiring has been completed. The lower Eicas is not implemented yet. Using screens I already had, kept the cost down as my personal priority is on building the overhead panel and adding modules. The touchscreen was a gift from a friend who didn't use it anymore. Ever since friends and collegues hear of my project they sometimes actively offer me their old PC or screen. Now you could make a different choice here. Some builders tell me that the immersion effect is great when utilizing a projector. Others are awed by uzing multiple high res CRT's. You can buy new, you can use old. I'm waiting for a defect projector to show up and replace the defect lamp. For the FMC/CDU screen some use 7 inch LCD's. Anyway, for me it is hard to give you a cost estimate here, but if you know what your preference would be, shop around to get a price indication. And again, you can add better screens over time.
Hardware Modules: Today I have a CPflight MCP, EFIS and NAV panel ready to use, plug and play, this approximately adds up to Euro 1000. I want to add more modules so this amount will go up. It is my choice to buy ready to go modules as they are designed for the 737 and represent the real thing. It is also possible to buy modules that have a lower cost, but these don't have the look I want, this is a personal choice. The other option is to build your own panels with all kinds of components like encoders, displays, switches, etc. I have no reference to what that would cost and you need to be "tech savvy" to build it. On Ebay a friend found and purchased a real 747 Cargo panel for me as a present. I'll try to hook it up through the phidgets even though it does not belong in a 737, nice experiment.
The next level of realism is to go for very realistic look, feel and functional modules for the FMC/CDU and Throttle Quadrant. My present CH products stick and throttle are ok, but to have a real throttle quadrant with autothrottle etc is a dream, the cost... Euro 1000 and higher.
Hardware I/O: There are many types of hardware I/O boards you can hook up your switches and pot's to. All I can say is to read user experiences in various forums and builders websites. I am involved in www.ifsbi.org and you can find a forum and several links from there to cockpit builders webpages, also check out fscockpit.com.
What I did was to go for Phidgets (phidgetsusa.com) because I can assign functions from pmSystems directly to Phidgets (you do need FSUIPC and WideFS made by Pete Dowson to be found at schiratti.com).
You can also use the interface software, to be found on the phidgetsusa site. My initial Phidgets puchase of 4 boards and all kinds of leds etc set me back 400 Euro's. Then you need (rotary)switches and wiring etc. Now this can also grow over time. I have spent Euro 100 on this, but will need more as I move on to the overhead panel. And I will need more Phidgets boards. So I am expecting this to head up into the total of Euro 1000 (including money already spent).
Panels: To have the most realistic view there are some companies that make laser engraved backlit panels. The big parts are the Main Instrument Panel(s), the Overhead panel and the Pedestal. These as a total would set you back between Euro 1000-2000 and then they still need to be wired. I decided for my first year of cockpit building to go for Do-It-Yourself using MDF panels and painting it grey. At a later stage I will convert to the more high fidelity panels. There are some new vendors on the block, so I expect the prices to go down. Including the MDF casing for screens, computers etc, which I put on wheels, I spent Euro 200 so far.
Cockpit shell:
It is possible to build/order the cockpit shell. This gives an enhanced immersion effect. Can't tell you much about this, so shop around on the web.
Documentation:
There are some nice books/manuals on the working of the airplane systems, FMC/CDU, checkrides etc. When you get into programming the system logics of your aircraft, reference material is of vital importance. There is free material to be found, but some people have taken the time and effort to write very comprehensive manuals, and this is where I buy it. Total so far Euro 180.
Motion Platform:
An area that will grow in the next years as it becomes more attainable for the humble soul. Soem builders are putting their own experiment together, some vendors are exploring the possibilities as far as I know.
Well, I hope this has shed some light on your questions, in my experience this will lead to more questions. Most of the remaining questions below, I have tried to answer in the story above.
I haven't grand totalled the amount spent by me so far, as it makes no sense to do so. It is a very personal choice how much you will spend and it doesn't take into account how you spread the investment over time. All I can say, is that it is well spent because this hobby is very enjoyable and every addition, big or small brings new joy to my flight simulation experience. And I made new friends in wonderful places who share this hobby and understand what I am talking about ;-)
Happy building and see you around.
Kester Meijer
kester@ifsbi.org
>2. Where do you buy parts for these masterpieces ?
see above
>3. How do you do it ???? I know I'm a complete noob.
start small and gradually expand over time. determine which parts of simulation have priority to you. Use the categories mentioned above and put them in your preferred sequence.
>4. Does it work with FS2004 ?
Yes, I use FS2004/FS9 for the outside view and PMDG for the aircraft model, not the PMDG panels though.
>5. Do you need any special software to make it work with FS9 ?
FSUIPC is a must have and when using multiple computers add WideFS to that list. And I would add pmSystems.
>6. If I built a DC-9 cockpit how do I connect it to FS9 and how do I use it with FS9 ?
see above
>7. Do I need payware DC-9 software ?? Something like the F1 Iron Knuckles DC9 ?
I suppose so just like I did with PMDG.