pylet
04-20-2008, 12:11 PM
Hi,
For quite awhile now everything has been working great. A couple of months ago I had a BSD of my FS9 PC so I had to re-build the C drive. This PC also had my MCP software on. But, for some reason I cannot get the c/o button to bring up a MACH number. At cruise FL350 the VNAV has .790 set. I select SPEED and the number 15 pops in the IAS window. I can adjust the speed knob but it does not adjust the .790 on the PFD. When I select c/o the IAS shows 270 as well as the PFD. I turn the speed knob and the PFD speed follows perfectly. I then push the c/o again and it goes back to 15 and the PFD goes to .790 MACH.
Any idea why my c/o button is not seeing the MACH properly or why the PFD MACH number does not adjust with the speed knob?
I have also noticed that in a climb I have 278/.778 set on the climb CDU page but the MACH is never captured. The aircraft maintains 278 knots right into the red at the higher altitudes during climb. I have the same problem when descending, I hit the level change button and the MACH window shows 15. I never had this problem since rebuilding my PC. I have FDS hardware MCP/CDU.
Plus when I select a new altitude my VS goes to +4500 fpm and the aircraft starts climbing even if I selected a lower altitude. The don't have to select VS, it just pops up as soon as I change the altitude window.
OK last weird thingy... I notice in the FSD CDU that the GW comes up wierd. It'll have something like 15.9 (122.3) in the top left LSK. I have to enter 122.3 in the LSK to get the rest of the FMC to program correctly. Usually the smaller number is my fuel load. Why would my fuel load show up there rather than my actual GW I'm not sure.
Following is a copy of my INI files. Hopefully someone will see my errors. Thanks in adavance:
=======================
pmFileCheck Build 29
Opening Connections
Local Path: Z:\Everyone
Checking Computer and User Name
Local Computer Name: DELL
Local User Name: Lyle
FSUIPC/WideFS found!
FSUIPC Version 3.8
WideServer Version 6.75
WideClient Version 6.75
Flight Simulator Running
Testing Framerate
Avg / Min / Max: 23.4 / 21.8 / 30.7
OK - GC Detected
GC Build 452
OK - FMC Detected (CDU or MCDU)
FMC Build 394
OK - A/P Detected (MCP or FCU)
A/P Build 422
Local DLL Files Found:
pm.dll dated: 1/12/2005 9:07:59 AM
Checking FS Path
OK - Reported FS Path \\DELL\Flight Simulator 9\
Trying to access FS Path
OK - Read access to FS Path
OK - Read/Write access to FS Path
OK - Read/Write access to FS Path
Wide Server reports:
42938 Connected to computer "PFD" running WideClient version 6.750 (skt=2720) TCP
42969 Connected to computer "LAPTOP" running WideClient version 6.750 (skt=2732) TCP
44938 Connected to computer "GT1" running WideClient version 6.750 (skt=2752) TCP
Looking for NETDIR from CDU
Reported NetDir is: \\gt1\netdir\
Checking PMNETDIR Path (FMC Generated Path)
>\\gt1\netdir\CDUType.bin
>\\gt1\netdir\CDUType.txt
>\\gt1\netdir\route.bin
>\\gt1\netdir\routeout.xml
>\\gt1\netdir\thrust.bin
>\\gt1\netdir\tmp.pln
6 File(s) found in NetDir, last date is 4/13/2008 1:08:47 PM
Checking FSPLANS Path (To Load/Save FS Flightplans)
OK - Read/Write access to FSPLANS Shared Folder
12 File(s) found in FSPLANS, last date is 4/13/2008 1:07:47 PM
last flight plan file is PAFA-PANC.PLN
dated: 4/13/2008 10:02:21 AM
Closing Everything
4/13/2008 1:11:48 PM
===================
===================
[Project Magenta MCP]
Build#422
[Display]
Title=Off
Menu=Off
WindowName=MCP/Enhanced Autopilot by Enrico Schiratti - Build 422
Topmost=Off
FSWindow=Off
Minimized=Off
NoMinimize=Off
[User]
Log=Off
SerialLog=Off
CycleMilliSeconds= 100
Top=-480000
Left=-480000
Width737= 2400
Height737= 360
Width747= 15360
Height747= 3345
Width777= 11925
Height777= 2460
MCPType=737
Intervent737=Off
ClassicEFISSel=Off
DelayMouseClick=On
Font=mcpfont
FontFactor= 1.27
[VNAV]
DescentSpeedControl=On
[Aircraft]
MinIAS= 0
DefaultIAS= 130
DefaultAltitude= 6000
AutoHDG=On
AutoVS=On
MachAltitude= 0
AutoCRS=Off
AllowStabTrimOverride=Off
StabTrimDeflect= 6000
Rollout=On
DisableAdd20Kts=Off
NoModeAfterTOGA=Off
UsePanel=On
PushButton=Off
SpeedProtect=Off
SELCurrentSpeed=On
Flare= 45
N1ref= 91.6
N1TOref= 91.6
N1GAref= 90
N1CLBref= 86.5
N1CRZref= 95.1
ThrRedAlt= 0
MaxROC= 6000
MaxROD= 6000
ClimbThrustLimiter=On
DisableAutobrakes=Off
DisableBrakes=Off
SwapCRS=Off
[Input]
MouseWheel=On
MouseWheelInvert=On
FSBusWriteBack=Off
[Autopilot]
AP_BetaTest=Off
[SerialConnection]
PFCComm= 5
PFC9600=Off
CautionThroughPass=Off
ForceHardwareLight=On
IgnoreBattery=Off
CPFlightComm= 0
CPFlightIO=Off
FDS_G1_Comm= 5
DakenSkys_IFS_Comm= 0
ElanComm= 0
ElanBaudRate=
AerosoftComm= 0
AerosoftFPV= 14
AerosoftDHRST= 0
/EicasButton1=???
[EPIC]
DisableRemoteMCP=Off
=====================
=====================
[Project Magenta CDU]
Build#394
[Display]
Title=Off
WindowName=Project Magenta CDU - Build 394
Topmost=Off
FSWindow=Off
FSFocus=Off
Minimize=Off
[Network]
DisableAutoNetDir=Off
NetDir=\\GT1\netdir\
SBPPath=\\Server\SquawkBox3\
[Flight]
LimitMCPSpeed=Off
AutoFlapRetract=Off
AutoFlapExtract=Off
[User]
LastBuild= 394
DeleteCFPFiles=Off
EngravityComm= 0
ElanComm= 0
Font=pmbcdu
FontNoSerif=Off
FontBold=On
FontFactor= .5
Text=white
BackgroundBlue=Off
PreFlight=Full
NoSelPrompt=Off
NoAwyPrompt=Off
Flush=On
FlushOnLand=On
DescendNowNM= 50
Messages=On
NoCOMXPDR=Off
KeyboardLights=On
KeyboardLightsXP=On
AutoKeyLayout=On
KeyLayout=N1
PageUpdate= .8
RemotePageUpdate= 1
AutoILSLOC=Off
ShowFrqinRoute=On
CLBThrOAT=On
PlanStep=Off
AutoGear=Off
DisableDoubleClick=Off
NoFSGWT=Off
Case=Brown
Log=Off
StrobeLights=Off
StrobeBacklight=Off
[OpenGL]
UseOpenGL=On
FontSmoothViaPolygons=Off
UseOpenGLFull=On
SetOpenGLFull=On
OpenGLFullX= 4
OpenGLFullY= 70
OpenGLFullZ= 0
OpenGLFullWidth= 3
OpenGLFullHeight= 4
OpenGLFullFontSize=-30
OpenGLFullSpacing=-4
OpenGLFullScratchPad= 2
OpenGLFullTitleText=-30
OpenGLFullRotate= 0
[Max]
Full=Off
FullTopmost=Off
FullNoFrame=On
InvertFull=Off
ScreenTop= 0
ScreenLeft= 0
ScreenHeight= 5175
ScreenWidth= 9600
TextTop= 353
TextLeft= 475
TextWidth= 6933
TextOffset= 980
[COMMAND Keyboard Codes]
===================
===================
lthrust.txt
Update= 3
KeyLayout=N1
Flare= 45
AircraftType=B737-700
CrzAlt= 35000
N1ref= 89.2
N1toref= 89.2
N1garef= 90
N1clbref= 0
N1crzref= 0
Spd1Pct= 100
Spd2Pct= 100
LimPct= 100
FlchPct= 100
MachPct= 100
TRAlt= 0
SpeedProtect=Off
vmaxls= 340
vminls= 193
v1= 120
vr= 122
v2= 131
vref= 126
transition= 18000
throttlesync=Off
stallpitchfactor= 0
stallbankfactor= 0
engineoutfactor= 0
gmtcorr= 0
maxmach= 819
AutoVNAV=Off
==========================
For quite awhile now everything has been working great. A couple of months ago I had a BSD of my FS9 PC so I had to re-build the C drive. This PC also had my MCP software on. But, for some reason I cannot get the c/o button to bring up a MACH number. At cruise FL350 the VNAV has .790 set. I select SPEED and the number 15 pops in the IAS window. I can adjust the speed knob but it does not adjust the .790 on the PFD. When I select c/o the IAS shows 270 as well as the PFD. I turn the speed knob and the PFD speed follows perfectly. I then push the c/o again and it goes back to 15 and the PFD goes to .790 MACH.
Any idea why my c/o button is not seeing the MACH properly or why the PFD MACH number does not adjust with the speed knob?
I have also noticed that in a climb I have 278/.778 set on the climb CDU page but the MACH is never captured. The aircraft maintains 278 knots right into the red at the higher altitudes during climb. I have the same problem when descending, I hit the level change button and the MACH window shows 15. I never had this problem since rebuilding my PC. I have FDS hardware MCP/CDU.
Plus when I select a new altitude my VS goes to +4500 fpm and the aircraft starts climbing even if I selected a lower altitude. The don't have to select VS, it just pops up as soon as I change the altitude window.
OK last weird thingy... I notice in the FSD CDU that the GW comes up wierd. It'll have something like 15.9 (122.3) in the top left LSK. I have to enter 122.3 in the LSK to get the rest of the FMC to program correctly. Usually the smaller number is my fuel load. Why would my fuel load show up there rather than my actual GW I'm not sure.
Following is a copy of my INI files. Hopefully someone will see my errors. Thanks in adavance:
=======================
pmFileCheck Build 29
Opening Connections
Local Path: Z:\Everyone
Checking Computer and User Name
Local Computer Name: DELL
Local User Name: Lyle
FSUIPC/WideFS found!
FSUIPC Version 3.8
WideServer Version 6.75
WideClient Version 6.75
Flight Simulator Running
Testing Framerate
Avg / Min / Max: 23.4 / 21.8 / 30.7
OK - GC Detected
GC Build 452
OK - FMC Detected (CDU or MCDU)
FMC Build 394
OK - A/P Detected (MCP or FCU)
A/P Build 422
Local DLL Files Found:
pm.dll dated: 1/12/2005 9:07:59 AM
Checking FS Path
OK - Reported FS Path \\DELL\Flight Simulator 9\
Trying to access FS Path
OK - Read access to FS Path
OK - Read/Write access to FS Path
OK - Read/Write access to FS Path
Wide Server reports:
42938 Connected to computer "PFD" running WideClient version 6.750 (skt=2720) TCP
42969 Connected to computer "LAPTOP" running WideClient version 6.750 (skt=2732) TCP
44938 Connected to computer "GT1" running WideClient version 6.750 (skt=2752) TCP
Looking for NETDIR from CDU
Reported NetDir is: \\gt1\netdir\
Checking PMNETDIR Path (FMC Generated Path)
>\\gt1\netdir\CDUType.bin
>\\gt1\netdir\CDUType.txt
>\\gt1\netdir\route.bin
>\\gt1\netdir\routeout.xml
>\\gt1\netdir\thrust.bin
>\\gt1\netdir\tmp.pln
6 File(s) found in NetDir, last date is 4/13/2008 1:08:47 PM
Checking FSPLANS Path (To Load/Save FS Flightplans)
OK - Read/Write access to FSPLANS Shared Folder
12 File(s) found in FSPLANS, last date is 4/13/2008 1:07:47 PM
last flight plan file is PAFA-PANC.PLN
dated: 4/13/2008 10:02:21 AM
Closing Everything
4/13/2008 1:11:48 PM
===================
===================
[Project Magenta MCP]
Build#422
[Display]
Title=Off
Menu=Off
WindowName=MCP/Enhanced Autopilot by Enrico Schiratti - Build 422
Topmost=Off
FSWindow=Off
Minimized=Off
NoMinimize=Off
[User]
Log=Off
SerialLog=Off
CycleMilliSeconds= 100
Top=-480000
Left=-480000
Width737= 2400
Height737= 360
Width747= 15360
Height747= 3345
Width777= 11925
Height777= 2460
MCPType=737
Intervent737=Off
ClassicEFISSel=Off
DelayMouseClick=On
Font=mcpfont
FontFactor= 1.27
[VNAV]
DescentSpeedControl=On
[Aircraft]
MinIAS= 0
DefaultIAS= 130
DefaultAltitude= 6000
AutoHDG=On
AutoVS=On
MachAltitude= 0
AutoCRS=Off
AllowStabTrimOverride=Off
StabTrimDeflect= 6000
Rollout=On
DisableAdd20Kts=Off
NoModeAfterTOGA=Off
UsePanel=On
PushButton=Off
SpeedProtect=Off
SELCurrentSpeed=On
Flare= 45
N1ref= 91.6
N1TOref= 91.6
N1GAref= 90
N1CLBref= 86.5
N1CRZref= 95.1
ThrRedAlt= 0
MaxROC= 6000
MaxROD= 6000
ClimbThrustLimiter=On
DisableAutobrakes=Off
DisableBrakes=Off
SwapCRS=Off
[Input]
MouseWheel=On
MouseWheelInvert=On
FSBusWriteBack=Off
[Autopilot]
AP_BetaTest=Off
[SerialConnection]
PFCComm= 5
PFC9600=Off
CautionThroughPass=Off
ForceHardwareLight=On
IgnoreBattery=Off
CPFlightComm= 0
CPFlightIO=Off
FDS_G1_Comm= 5
DakenSkys_IFS_Comm= 0
ElanComm= 0
ElanBaudRate=
AerosoftComm= 0
AerosoftFPV= 14
AerosoftDHRST= 0
/EicasButton1=???
[EPIC]
DisableRemoteMCP=Off
=====================
=====================
[Project Magenta CDU]
Build#394
[Display]
Title=Off
WindowName=Project Magenta CDU - Build 394
Topmost=Off
FSWindow=Off
FSFocus=Off
Minimize=Off
[Network]
DisableAutoNetDir=Off
NetDir=\\GT1\netdir\
SBPPath=\\Server\SquawkBox3\
[Flight]
LimitMCPSpeed=Off
AutoFlapRetract=Off
AutoFlapExtract=Off
[User]
LastBuild= 394
DeleteCFPFiles=Off
EngravityComm= 0
ElanComm= 0
Font=pmbcdu
FontNoSerif=Off
FontBold=On
FontFactor= .5
Text=white
BackgroundBlue=Off
PreFlight=Full
NoSelPrompt=Off
NoAwyPrompt=Off
Flush=On
FlushOnLand=On
DescendNowNM= 50
Messages=On
NoCOMXPDR=Off
KeyboardLights=On
KeyboardLightsXP=On
AutoKeyLayout=On
KeyLayout=N1
PageUpdate= .8
RemotePageUpdate= 1
AutoILSLOC=Off
ShowFrqinRoute=On
CLBThrOAT=On
PlanStep=Off
AutoGear=Off
DisableDoubleClick=Off
NoFSGWT=Off
Case=Brown
Log=Off
StrobeLights=Off
StrobeBacklight=Off
[OpenGL]
UseOpenGL=On
FontSmoothViaPolygons=Off
UseOpenGLFull=On
SetOpenGLFull=On
OpenGLFullX= 4
OpenGLFullY= 70
OpenGLFullZ= 0
OpenGLFullWidth= 3
OpenGLFullHeight= 4
OpenGLFullFontSize=-30
OpenGLFullSpacing=-4
OpenGLFullScratchPad= 2
OpenGLFullTitleText=-30
OpenGLFullRotate= 0
[Max]
Full=Off
FullTopmost=Off
FullNoFrame=On
InvertFull=Off
ScreenTop= 0
ScreenLeft= 0
ScreenHeight= 5175
ScreenWidth= 9600
TextTop= 353
TextLeft= 475
TextWidth= 6933
TextOffset= 980
[COMMAND Keyboard Codes]
===================
===================
lthrust.txt
Update= 3
KeyLayout=N1
Flare= 45
AircraftType=B737-700
CrzAlt= 35000
N1ref= 89.2
N1toref= 89.2
N1garef= 90
N1clbref= 0
N1crzref= 0
Spd1Pct= 100
Spd2Pct= 100
LimPct= 100
FlchPct= 100
MachPct= 100
TRAlt= 0
SpeedProtect=Off
vmaxls= 340
vminls= 193
v1= 120
vr= 122
v2= 131
vref= 126
transition= 18000
throttlesync=Off
stallpitchfactor= 0
stallbankfactor= 0
engineoutfactor= 0
gmtcorr= 0
maxmach= 819
AutoVNAV=Off
==========================