Lewis Simmons
06-01-2008, 04:42 AM
Well today I started work on the 787 MIP. Not too bad at the moment, once I get a real CAD designer or I get google sketchup pro, I will put all the fine detail into a new, more specific design and I will simulate all the bells and whistles being put into place.
At the moment with Version 1.1 I guess, the grey side is the front side and the whole you see are for screws. I have had no measurements to work with, only pictures so the measurements may be out a bit but shouldn't be by much.
The back (white) is where you can see all the connections and looks a bit like lego. I'm open to suggestions for better ways to connect the different sections marked out but at the moment I am happy with this. Later I will add the real large pieces like the MCP frame and MIP support, but that will probably be when I use the real CAD drawer.
Here you go, 787 MIP Version 1.1
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-02-14.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-09-37-59.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-09-18-01.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-08-50-45.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-12-30-51-1.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-12-03-43.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-55-71.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-18-09.jpg
At the moment with Version 1.1 I guess, the grey side is the front side and the whole you see are for screws. I have had no measurements to work with, only pictures so the measurements may be out a bit but shouldn't be by much.
The back (white) is where you can see all the connections and looks a bit like lego. I'm open to suggestions for better ways to connect the different sections marked out but at the moment I am happy with this. Later I will add the real large pieces like the MCP frame and MIP support, but that will probably be when I use the real CAD drawer.
Here you go, 787 MIP Version 1.1
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-02-14.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-09-37-59.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-09-18-01.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-08-50-45.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-12-30-51-1.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-12-03-43.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-55-71.jpg
http://i174.photobucket.com/albums/w100/vac3087/SketchUp2008-06-0120-10-18-09.jpg