GC466 and new EICAS Messages

[jb747]

With the release of GC466 several EICAS messages previously incorporated into pmSystems have been moved to the GC software to reduce display latency. pmSystems142 has been modified accordingly. However, if you have developed custom logic files you might want to review the list below and make adjustments to your files as necessary.

This is of most interest to B747 drivers, but other models also have developed EICAS messages sets.

The following EICAS messages and logic parameters have been implemented in gc466 that was released yesterday. For those of you that have customized your own logic files it might be of some value.

Cheers,

Jon
------------

APU RUNNING' (apun > 20) and (apumode <> 4)
ELEC GEN OFF 1' gen1fault
ELEC GEN OFF 2' gen2fault
ELEC GEN OFF 3' gen3fault
ELEC GEN OFF 4' gen4fault
FUEL PUMP 1 FWD' fwd1pumpfault
FUEL PUMP 2 FWD' fwd2pumpfault
FUEL PUMP 3 FWD' fwd3pumpfault
FUEL PUMP 4 FWD' fwd4pumpfault
FUEL PUMP 1 AFT' aft1pumpfault
FUEL PUMP 2 AFT' aft2pumpfault
FUEL PUMP 3 AFT' aft3pumpfault
FUEL PUMP 4 AFT' aft4pumpfault
>YAW DAMPER UPR' yawdamperfault
>YAW DAMPER LWR' yawdamperfault2
HYD PRESS DEM 1' hydswitch1 = 0
HYD PRESS DEM 2' hydswitch2 = 0
HYD PRESS DEM 3' hydswitch3 = 0
HYD PRESS DEM 4' (hydswitch4 = 0) or (hydswitch4 = 3)
HYD PRESS ENG 1' hydraulic1 < 2000
HYD PRESS ENG 2' hydraulic2 < 2000
HYD PRESS ENG 3' hydraulic3 < 2000
HYD PRESS ENG 4' hydraulic4 < 2000
CON IGNITION ON' constart
PACK 2+3 OFF' (pack1>0) and (pack2=0) and (pack3=0)
PACKS OFF' (pack1=0) and (pack2=0) and (pack3=0)
PACK 1 OFF' (pack1=0) and (pack2>0) and (pack3>0)
PACK 2 OFF' (pack1>0) and (pack2=0) and (pack3>0)
PACK 3 OFF' (pack1>0) and (pack2>0) and (pack3=0)
PACK 1+2 OFF' (pack1=0) and (pack2=0) and (pack3>0)
PACK 1+3 OFF' (pack1=0) and (pack2>0) and (pack3=0)
IRS ALIGN MODE L' (IRSSelector1=2) and (IRSNotAligned=1)
IRS ALIGN MODE C' (IRSSelector2=2) and (IRSNotAligned=1)
IRS ALIGN MODE R' (IRSSelector3=2) and (IRSNotAligned=1)
BLEED 1 OFF' (Eng1Bleed=0) and (fs1n1>8)
BLEED 2 OFF' (Eng2Bleed=0) and (fs2n1>8)
BLEED 3 OFF' (Eng3Bleed=0) and (fs3n1>8)
BLEED 4 OFF' (Eng4Bleed=0) and (fs4n1>8)
ENGINE1 SHUTDOWN' Cutoff1 = 1 and (fs1n1 > 8)
ENGINE2 SHUTDOWN' Cutoff2 = 1 and (fs2n1 > 8)
ENGINE3 SHUTDOWN' Cutoff3 = 1 and (fs3n1 > 8)
ENGINE4 SHUTDOWN' Cutoff4 = 1 and (fs4n1 > 8)
>BATTERY OFF' batt1 = 0
>BAT DISCH APU' standbypower = 2
>BAT DISCH MAIN' standbypower = 2
>TRIM AIR OFF' TrimAir = 0
FIRE APU' FireDet5=1
FIRE ENG 1' FireDet1=1
FIRE ENG 2' FireDet2=1
FIRE ENG 3' FireDet3=1
FIRE ENG 4' FireDet4=1
HEAT WINDOW L' WindowHeatFL = 0
HEAT WINDOW R' WindowHeatFR = 0
ELEC UTIL BUS L' UtilityLoff=1
ELEC UTIL BUS R' UtilityRoff=1
SPD BRK ARM' fsspeedbrakearm=1
STROBE LIGHT' (fsstrobe=0) and (fsonground=0)
FUEL OVRD 2 FWD' Fwd2PumpAuxFault
FUEL OVRD 2 AFTD' Aft2PumpAuxFault
FUEL OVRD 3 FWD' Fwd3PumpAuxFault
FUEL OVRD 3 AFTD' Aft3PumpAuxFault
ELEC BUS ISLN 1' (BustieOff1 = 1) and (fs1n1 > 8)
ELEC BUS ISLN 2' (BustieOff2 = 1) and (fs2n1 > 8)
ELEC BUS ISLN 3' (BustieOff3 = 1) and (fs3n1 > 8)
ELEC BUS ISLN 4' (BustieOff4 = 1) and (fs4n1 > 8)
AIRSPEED LOW' stallwarning = 1
OVERSPEED' overspeedwarning = 1
ENG1 FAIL' Eng1Fail=1 and (fsonground =0)
ENG2 FAIL' Eng2Fail=1 and (fsonground =0)
ENG3 FAIL' Eng3Fail=1 and (fsonground =0)
ENG4 FAIL' Eng4Fail=1 and (fsonground =0)
FUEL PRES STAB L' Stab1pumpfault=1
FUEL PRES STAB R' Stab2pumpfault=1
FUEL PRESS CTR L' Ctr1pumpfault=1
FUEL PRESS CTR R' Ctr2pumpfault=1
FUEL PRESS ENG 1' fwd1pumpfault and aft1pumpfault and (FuelCrossFeed=0)
FUEL PRESS ENG 2' fwd2pumpfault and fwd2pumpauxfault and aft2pumpfault and aft2pumpauxfault
FUEL PRESS ENG 3' fwd3pumpfault and fwd3pumpauxfault and aft3pumpfault and aft3pumpauxfault
FUEL PRESS ENG 4' fwd4pumpfault and aft4pumpfault and (FuelCrossFeed4=0)
HYD PRESS SYS 1' (hydraulic1 < 10000) and (fs1n1 > 8)
HYD PRESS SYS 2' (hydraulic2 < 10000) and (fs2n1 > 8)
HYD PRESS SYS 3' (hydraulic3 < 10000) and (fs3n1 > 8)
HYD PRESS SYS 4' (hydraulic4 < 10000) and (fs4n1 > 8)