capt_pero
10-09-2013, 12:52 AM
Hi,
I am quite a newbie in JeeHell in SIOC. That's the reason why I start step by step with my overheadpanel (AntiIce Panel) to build up a fixed based A320 (once upon...)
I use:
- OC USB Extention J1 <> OC MasterCard P1
- OC USB Outputs <> Out 63 LED
My first SIOC configuration was to get LED 63 lighted if APU Availible LED is on.
That's my config:
// *****************************************************************************// * Config_SIOC ver 4.5 - By Manuel Velez - www.opencockpits.com
// *****************************************************************************
// * FileName : sioc.txt
// * Date : 09.10.2013
Var 0001, name APUmasterSW, Link IOCARD_SW, Device 1, Input 1
For testing I press:
1) Both BAT switches at the Jeehell Overhead Panel (Software)
2) APU Master Switch
3) APU Start Switch
After pressing APU Master Switch LED 63 is getting lighted and I don't understand why...
After APU Start Switch is pressed LED 63 turned off until AVAIL is on (then LED 63 turns on again)...
I am a bit confused.
I changed allready LED 63 to another output to avoid a defective output but same behaviour with another output.
My SIOC.INI:
[ fichero de configuracion para el SIOC ver. 4.5 ]
[ Configuration file for SIOC ]
[************** SIOC ***************]
[ Nombre asignado al SIOC ]
[ SIOC name ]
Name=Main
[ Puerto del servidor IOCP ]
[ IOCP port ]
IOCP_port=8092
[ Tiempo de respuesta máximo de los paquetes IOCP ]
[ IOCP Timeout ]
IOCP_timeout=4000
[ Arranque minimizado en la barra ]
[ Start minimized in tray ]
Minimized=No
[ Retraso necesario para las variables toggles (Project Magenta)]
[ Deley needed for var. toggles (Project Magenta) ]
toggle_delay=20
[ Fichero de configuracion ]
[ Configuration File ]
CONFIG_FILE=.\JeeHellWare.ssi
[************** MONITOR MODULE ***************]
[ Desabilitar monitorizacion remota del SIOC ]
[ Remote monitor disable mode yes/no ]
Monitor_disable=No
[ Refresco broadcast monitor (en segundos) ]
[ Broadcast monitor time (seconds) ]
Monitor_time=2
[************** IOCARDS MODULE ***************]
[ Desactivar el módulo de las IOCards ]
[ Disable IOCards module ]
IOCard_disable=No
[ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ]
[ Frequency divisor for delay the analogic axes. (1-999)]
Divisor_AD=10
[------------- CARDS CONFIG -------------]
[ IOCard Master ]
[...............]
[ Spanish : ]
[ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ tipo = 0 : Emulador de Master Card // OBSOLETO ]
[ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ]
[ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ]
[ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ]
[ tipo = 4 : Tarjeta USBExpansion usada ]
[ tipo = 5 : Modulo MCP de Opencockpits ]
[ tipo = 6 : Tarjeta USBOutputs ]
[ tipo = 7 : Modulo EFIS de Opencockpits ]
[ tipo = 8 : Modulo Radio COM de Opencockpits ]
[ tipo = 9 : Modulo Radio NAV de Opencockpits ]
[ tipo = 10 : Modulo Radio ADF de Opencockpits ]
[ tipo = 11 : Modulo Radio ATC de Opencockpits ]
[ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ]
[ tipo = 13 : Modulo FMC-737 de Opencockpits ]
[ tipo = 14 : Tarjeta USBDcmotorPLUS ]
[ tipo = 15 : Modulo MCP V3 de Opencockpits ]
[ tipo = 16 : Modulo CRONOMETRO B737 ]
[ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ]
[ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ]
[ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]
[ Un ejemplo de conexión a simulador ]
[ MASTER=0,0,1,0 ]
[ English : ]
[ MASTER=(Device index),(Type),(Number of cards),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ type = 0 : Master Card Emulator // OBSOLETE ]
[ type = 1 : Master Card connected directly to parallel port // OBSOLETE ]
[ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE]
[ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ]
[ type = 4 : USBExpansion Card used ]
[ type = 5 : Opencockpits MCP module ]
[ type = 6 : USBOutputs Card used ]
[ type = 7 : EFIS module ]
[ type = 8 : Radio COM module ]
[ type = 9 : Radio NAV module ]
[ type = 10 : Radio ADF module ]
[ type = 11 : Radio ATC module ]
[ type = 12 : Radio RMP Airbus module ]
[ type = 13 : FMC-737 module ]
[ type = 14 : USBDCmotorPLUS Card used ]
[ type = 15 : MCP V3 module ]
[ type = 16 : CHRONO B737 module ]
[ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ]
[ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ]
[ For example, two USBExpansion cards connected with 3 and 2 Master cards used ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]
[ For example, use of Master card emulator ]
[ MASTER=0,0,1,0 ]
[ Use the first USBExpansion card connected with only one Master Card attached ]
[ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ]
[MASTER=3,6,1,252]
[MASTER=0,4,1,0]
[MASTER=0,12,1,0]
[MASTER=0,16,1,0]
[ Others Cards / Otras tarjetas ]
[...............................]
[ Spanish : ]
[ Nombre_de_tarjeta=(Indice device),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ]
[ English : ]
[ Name_of_card=(Device index),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ]
[ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ]
[ Example of two USBServos for index 0 and 1, and device number 17 and 23 ]
[ USBServos=0,17 ]
[ USBServos=1,23 ]
[USBStepper=0,0]
[USBKeys=0,0]
[USBServos=0,0]
[USBRelays=0,0]
[USBDCmotor=0,0]
[ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ]
[ For analogic axles, you use the device number of cards what allow the axles ]
[USBAnalogic=0,0]
[************** FSUIPC MODULE ***************]
[ Desabilitar lectura de las FSUIPC ]
[ FSUIPC disable mode yes/no ]
FSUipcdisable=No
[ Refresco recepción FSUIPC ]
[ FSUIPC refresh ]
FSUipcRefresh=50
[************** IOCP CLIENTS MODULES ***************]
[ Retraso para inicializacion una vez conectado el cliente en milisegundos ]
[ Delay for initialization when client has been connected in mseconds ]
IOCPini_delay=3000
[************** IOCP CLIENT MODULE #0 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient0_disable=No
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient0_host=localhost
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient0_port=8099
[************** IOCP CLIENT MODULE #1 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient1_disable=yes
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient1_host=localhost
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient1_port=8099
[************** SOUND MODULE ***************]
[ Ficheros de sonido ]
[ Sound Files ]
[ Desactivar el módulo de sonido ]
[ Disable Sound module ]
Sound_disable=yes
[ Volumen general de los sonidos 0-100 ]
[ Master Volume 0-100 ]
Volume=100
[ put '*' first filename for loop Sound ]
[ anteponer '*' en el fichero para bucle continuo de sonido]
[ Sound=wav_file,frequency,volume,pan ]
[ frequency=100 to 100000 0=original -1=current ]
[ volume=0 to 100, -1=current ]
[ pan=-100 (left) to +100 (right) 0=center -1=current ]
[ Sound=Fichero_wav,frecuencia,volumen,balance ]
[ frecuencia=100 hasta 100000 0=original -1=Por defecto ]
[ volumen=0 hasta 100 -1=Volumen por defecto ]
[ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ]
[ #1 ]
Sound=APDis.wav,-1,-1,-1
[ #2 ]
Sound=*outermk.wav,-1,-1,-1
[ #3 ]
Sound=*hello.wav
[************** KEYBOARD EMULATOR MODULE ***************]
[ Nombre exacto de la ventana donde se enviarán las teclas ]
[ Name of window for key send ]
[window = "Project Magenta Glass Cockpit - Build 396" ]
window =a.txt - Bloc de notas
[ Asignación de teclas ]
[ assign youe keys ]
#1=A
#2=B
#3=C
#4=D
#5=E
#6=F
#7=G
#8=H
#9=I
#10=J
#11=K
#12=L
#13=M
#14=N
#15=O
#16=P
#17=Q
#18=R
#19=S
#20=T
#21=U
#22=V
#23=W
#24=X
#25=Y
#26=Z
#27=1
#28=2
#29=3
#30=4
#31=5
#32=6
#33=7
#34=8
#35=9
#36=0
#37=<
#38=,
#39=.
#40=-
#41=*
#42=+
#43=//
#44=/0
#45=/1
#46=/A
#47=
#48=
#49=
#50=
#51=
#52=
#53=
#54=
#55=
#56=
#57=
#58=
#59=
#60=
#61=
#62=
#63=
#64=
#65=
#66=
#67=
#68=
#69=
#70=
#71=
#72=
#73=
#74=
#75=
#76=
#77=
#78=
#79=
#80=
#81=
#82=
#83=
#84=
#85=
#86=
#87=
#88=<a
#200=B
[ --- SIOC Autoconfig Devices Ver 4.5B1 ==> 09.10.2013 06:05:00 <== ----]
MASTER=1,4,1,11
MASTER=0,6,1,5
Would be nice if you can light up my brain... ;O)
Regards,
pero
I am quite a newbie in JeeHell in SIOC. That's the reason why I start step by step with my overheadpanel (AntiIce Panel) to build up a fixed based A320 (once upon...)
I use:
- OC USB Extention J1 <> OC MasterCard P1
- OC USB Outputs <> Out 63 LED
My first SIOC configuration was to get LED 63 lighted if APU Availible LED is on.
That's my config:
// *****************************************************************************// * Config_SIOC ver 4.5 - By Manuel Velez - www.opencockpits.com
// *****************************************************************************
// * FileName : sioc.txt
// * Date : 09.10.2013
Var 0001, name APUmasterSW, Link IOCARD_SW, Device 1, Input 1
For testing I press:
1) Both BAT switches at the Jeehell Overhead Panel (Software)
2) APU Master Switch
3) APU Start Switch
After pressing APU Master Switch LED 63 is getting lighted and I don't understand why...
After APU Start Switch is pressed LED 63 turned off until AVAIL is on (then LED 63 turns on again)...
I am a bit confused.
I changed allready LED 63 to another output to avoid a defective output but same behaviour with another output.
My SIOC.INI:
[ fichero de configuracion para el SIOC ver. 4.5 ]
[ Configuration file for SIOC ]
[************** SIOC ***************]
[ Nombre asignado al SIOC ]
[ SIOC name ]
Name=Main
[ Puerto del servidor IOCP ]
[ IOCP port ]
IOCP_port=8092
[ Tiempo de respuesta máximo de los paquetes IOCP ]
[ IOCP Timeout ]
IOCP_timeout=4000
[ Arranque minimizado en la barra ]
[ Start minimized in tray ]
Minimized=No
[ Retraso necesario para las variables toggles (Project Magenta)]
[ Deley needed for var. toggles (Project Magenta) ]
toggle_delay=20
[ Fichero de configuracion ]
[ Configuration File ]
CONFIG_FILE=.\JeeHellWare.ssi
[************** MONITOR MODULE ***************]
[ Desabilitar monitorizacion remota del SIOC ]
[ Remote monitor disable mode yes/no ]
Monitor_disable=No
[ Refresco broadcast monitor (en segundos) ]
[ Broadcast monitor time (seconds) ]
Monitor_time=2
[************** IOCARDS MODULE ***************]
[ Desactivar el módulo de las IOCards ]
[ Disable IOCards module ]
IOCard_disable=No
[ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ]
[ Frequency divisor for delay the analogic axes. (1-999)]
Divisor_AD=10
[------------- CARDS CONFIG -------------]
[ IOCard Master ]
[...............]
[ Spanish : ]
[ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ tipo = 0 : Emulador de Master Card // OBSOLETO ]
[ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ]
[ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ]
[ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ]
[ tipo = 4 : Tarjeta USBExpansion usada ]
[ tipo = 5 : Modulo MCP de Opencockpits ]
[ tipo = 6 : Tarjeta USBOutputs ]
[ tipo = 7 : Modulo EFIS de Opencockpits ]
[ tipo = 8 : Modulo Radio COM de Opencockpits ]
[ tipo = 9 : Modulo Radio NAV de Opencockpits ]
[ tipo = 10 : Modulo Radio ADF de Opencockpits ]
[ tipo = 11 : Modulo Radio ATC de Opencockpits ]
[ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ]
[ tipo = 13 : Modulo FMC-737 de Opencockpits ]
[ tipo = 14 : Tarjeta USBDcmotorPLUS ]
[ tipo = 15 : Modulo MCP V3 de Opencockpits ]
[ tipo = 16 : Modulo CRONOMETRO B737 ]
[ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ]
[ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ]
[ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]
[ Un ejemplo de conexión a simulador ]
[ MASTER=0,0,1,0 ]
[ English : ]
[ MASTER=(Device index),(Type),(Number of cards),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ type = 0 : Master Card Emulator // OBSOLETE ]
[ type = 1 : Master Card connected directly to parallel port // OBSOLETE ]
[ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE]
[ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ]
[ type = 4 : USBExpansion Card used ]
[ type = 5 : Opencockpits MCP module ]
[ type = 6 : USBOutputs Card used ]
[ type = 7 : EFIS module ]
[ type = 8 : Radio COM module ]
[ type = 9 : Radio NAV module ]
[ type = 10 : Radio ADF module ]
[ type = 11 : Radio ATC module ]
[ type = 12 : Radio RMP Airbus module ]
[ type = 13 : FMC-737 module ]
[ type = 14 : USBDCmotorPLUS Card used ]
[ type = 15 : MCP V3 module ]
[ type = 16 : CHRONO B737 module ]
[ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ]
[ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ]
[ For example, two USBExpansion cards connected with 3 and 2 Master cards used ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]
[ For example, use of Master card emulator ]
[ MASTER=0,0,1,0 ]
[ Use the first USBExpansion card connected with only one Master Card attached ]
[ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ]
[MASTER=3,6,1,252]
[MASTER=0,4,1,0]
[MASTER=0,12,1,0]
[MASTER=0,16,1,0]
[ Others Cards / Otras tarjetas ]
[...............................]
[ Spanish : ]
[ Nombre_de_tarjeta=(Indice device),(Número device) ]
[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]
[ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ]
[ English : ]
[ Name_of_card=(Device index),(Device number) ]
[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]
[ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ]
[ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ]
[ Example of two USBServos for index 0 and 1, and device number 17 and 23 ]
[ USBServos=0,17 ]
[ USBServos=1,23 ]
[USBStepper=0,0]
[USBKeys=0,0]
[USBServos=0,0]
[USBRelays=0,0]
[USBDCmotor=0,0]
[ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ]
[ For analogic axles, you use the device number of cards what allow the axles ]
[USBAnalogic=0,0]
[************** FSUIPC MODULE ***************]
[ Desabilitar lectura de las FSUIPC ]
[ FSUIPC disable mode yes/no ]
FSUipcdisable=No
[ Refresco recepción FSUIPC ]
[ FSUIPC refresh ]
FSUipcRefresh=50
[************** IOCP CLIENTS MODULES ***************]
[ Retraso para inicializacion una vez conectado el cliente en milisegundos ]
[ Delay for initialization when client has been connected in mseconds ]
IOCPini_delay=3000
[************** IOCP CLIENT MODULE #0 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient0_disable=No
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient0_host=localhost
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient0_port=8099
[************** IOCP CLIENT MODULE #1 ***************]
[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient1_disable=yes
[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient1_host=localhost
[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient1_port=8099
[************** SOUND MODULE ***************]
[ Ficheros de sonido ]
[ Sound Files ]
[ Desactivar el módulo de sonido ]
[ Disable Sound module ]
Sound_disable=yes
[ Volumen general de los sonidos 0-100 ]
[ Master Volume 0-100 ]
Volume=100
[ put '*' first filename for loop Sound ]
[ anteponer '*' en el fichero para bucle continuo de sonido]
[ Sound=wav_file,frequency,volume,pan ]
[ frequency=100 to 100000 0=original -1=current ]
[ volume=0 to 100, -1=current ]
[ pan=-100 (left) to +100 (right) 0=center -1=current ]
[ Sound=Fichero_wav,frecuencia,volumen,balance ]
[ frecuencia=100 hasta 100000 0=original -1=Por defecto ]
[ volumen=0 hasta 100 -1=Volumen por defecto ]
[ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ]
[ #1 ]
Sound=APDis.wav,-1,-1,-1
[ #2 ]
Sound=*outermk.wav,-1,-1,-1
[ #3 ]
Sound=*hello.wav
[************** KEYBOARD EMULATOR MODULE ***************]
[ Nombre exacto de la ventana donde se enviarán las teclas ]
[ Name of window for key send ]
[window = "Project Magenta Glass Cockpit - Build 396" ]
window =a.txt - Bloc de notas
[ Asignación de teclas ]
[ assign youe keys ]
#1=A
#2=B
#3=C
#4=D
#5=E
#6=F
#7=G
#8=H
#9=I
#10=J
#11=K
#12=L
#13=M
#14=N
#15=O
#16=P
#17=Q
#18=R
#19=S
#20=T
#21=U
#22=V
#23=W
#24=X
#25=Y
#26=Z
#27=1
#28=2
#29=3
#30=4
#31=5
#32=6
#33=7
#34=8
#35=9
#36=0
#37=<
#38=,
#39=.
#40=-
#41=*
#42=+
#43=//
#44=/0
#45=/1
#46=/A
#47=
#48=
#49=
#50=
#51=
#52=
#53=
#54=
#55=
#56=
#57=
#58=
#59=
#60=
#61=
#62=
#63=
#64=
#65=
#66=
#67=
#68=
#69=
#70=
#71=
#72=
#73=
#74=
#75=
#76=
#77=
#78=
#79=
#80=
#81=
#82=
#83=
#84=
#85=
#86=
#87=
#88=<a
#200=B
[ --- SIOC Autoconfig Devices Ver 4.5B1 ==> 09.10.2013 06:05:00 <== ----]
MASTER=1,4,1,11
MASTER=0,6,1,5
Would be nice if you can light up my brain... ;O)
Regards,
pero