View Full Version : Phidgets v.4.3.65 with Win 10
Hello,
I am looking for help.
Everything works fine for me with W7 and FS2004.Now i am testing with Win 10 and P3D v 3.1 .
Everything is installed te same way as in W7 and when i start up the Phidgets Control Panel
it is not recognized, i mean the Phidget led 64 advanced serial number and version does not show up.
I have .Net 4.5
I can see the Phidgets Interface but when i start P3D v3.1 i get
Run time error 9 Subcript out of range .
What did i overlook?
Regards,
Hugo
Hello,
I solved part of the problem .
I switched the usb from usb connection 3 to connecction 2.
Most new motherboard have more con 3 instead con 2.
The only problem is that P3D and Fsuipc don't show up in the Phidget Interface 4.3.65
Anyone familiar with P3d and the Inteface ?
Regards,
Hugo
Hello again,
I upgrad with v 4.3.86 and indeed FSUIPC and P3d did show up.
In VARIABLE i did copy a IFLY737ini , BUTnow am stuck !
What is the right procedure to go on ?
Hugo
CocnutAir
03-02-2016, 11:42 AM
Your card settings are stored in the Cards directory. You will need to copy those files from your W7 system to your win 10 system.
Thanks for you quick reply.I posted a PM. I want to send a copy from my Phidgets Interface ,to check what is going wrong.
Thanks a lot,
Hugo
Hello,
I found the solution another udate to v. 4393 .All seem to be OK.
Hugo
Hi,
It seems i have another small problem.
Everything works fine with the USB plugged IN.
When i stop the PC and power off, restart PC , the Card is not recognized ,
until i plug out and plug in again ???
How come ?
Need some advise,
Hugo
alleycat
03-25-2016, 11:57 PM
I sometimes have this problem with one or two cards. I use 18 cards. Sometimes have same thing with powered usb hubs. Not sure if this a genrral usb or phidget problem. For now I just live with it.
Hi,
It seems i have another small problem.
Everything works fine with the USB plugged IN.
When i stop the PC and power off, restart PC , the Card is not recognized ,
until i plug out and plug in again ???
How come ?
Need some advise,
Hugo
alleycat
03-26-2016, 10:16 AM
I sometimes have this problem with one or two cards. I use 18 cards. Sometimes have same thing with powered usb hubs. Not sure if this a genrral usb or phidget problem. For now I just live with it.
I am assuming this also occurs on the Phidget Cosole (on the tray at bottom right in Win 7 - do not know where located, if at all, in Win 10)
Thanks for the reply ,gave up research ,will have to live with it too.
Hugo
Hello,
Right now i have another problem.Trying to connect my Phidgets card in W10 and P3dv3.5
i get RUN TIME ERROR 9 subschript out of range .
How can i solve this?
Hugo
alleycat
06-29-2016, 12:21 PM
Are you still using version 4.3.65?
Hello,
I used to have this in W7 FS2004.Did not seem to work in P3d v3.5. and W10 .Right now i am testing 43123 .
I can test the leds,but it seems that i overlook something , because i am stuck ,can't get respons from it ,on my upper panel.
I configure it, test each led ,what should i do next?
I also have to touch the green status led bar to see what has been assigned. and then i am stuck.
Maybe you can tell exactly how to proceed.
May i ask you another question ?
The usb connector has to be unplugged after each new PC startup ,i mean unplug and plug it again ,then i hear the sound that the USB is recogized! Why???
I even have this now with my Saitek PRO Flight Yoke. It works with plug in only, without any driver.
Many thanks,
Regards,
Hugo
Hi again,
I installed now 4.3.65 en overwrote it with 4.3.93.
In the installed box it stays YELLOW i guess it should be GREEN ? Why ?
Phidgets2 ver.2.1.8
feb 22 2016
PhidgetsCOMLibr 2.1.8
jan 9 2015
Testing LEDS is ok , but no respond with IFly ???
What is te missing link ?
Regads
Hugo
CocnutAir
07-10-2016, 05:07 PM
Not all Phidget driver versions are forward or backward compatible. You need to have the version that Fs2Phidget was built against. The boxes list the required version and the actual version you have installed. They must match including the date. You can download the required version from the Phidget web site and clicking on the Drivers tab. Have a look in the first paragraph of text and look for sentence. "If you need to access non-current versions...click here".
Hello,
It looks like the leds are working.I just has to open the programm as Administrator.
In Win 7 never had to do it. I guess this is new in Win 10 .
Hugo