Page 2 of 2 FirstFirst 12
Results 11 to 12 of 12
  1. 08-03-2010, 09:22 AM #11
    fsaviator
    fsaviator is offline
    Warren fsaviator's Avatar
    Join Date
    Dec 2008
    Location
    Dupont, WA
    Posts
    488
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Made my first cuts with my CNC

    I cut a section then shifted it over. A very time consuming process as you have to ensure that the MDF is straight each time. My orginal test cut had the rear pocekted out for the monitors... I haven't decided if I'm going to go that route yet. It's a lot of sawdust and mess to do away with a few millimeters of standoff on the monitors.
    Warren
    http://www.B737NG-SIM.com and https://www.facebook.com/fsaviator on facebook
    Reply With Quote Reply With Quote
  2. Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
    Thanks twisted8 thanked for this post
  3. 08-03-2010, 11:02 AM #12
    Westozy
    Westozy is offline
    MyCockpit Support Staff
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100



    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Made my first cuts with my CNC

    Quote Originally Posted by fsaviator View Post
    Gwyn, I would really appreciate access to your vcarve files... I'm still learning the software, and if anything, it will give me some squared away FS Panel oriented examples to learn from. My ultimate goal is to be able to make whatever panels I want.

    Cheers,

    Warren
    Send an email to me Warren!

    Cheers Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Previous Thread | Next Thread »

Similar Threads

  1. CNC made Flapgauge
    By Wendy in forum CNC Discussion
    Replies: 19
    Last Post: 10-06-2011, 11:30 AM
  2. Is there a 737NG MIP made in the USA??
    By 737NUT in forum General Builder Questions All Aircraft Types
    Replies: 5
    Last Post: 03-08-2011, 09:15 PM
  3. This made me laugh!
    By CessnaGuy in forum Pilots Lounge - Let your Hair down
    Replies: 2
    Last Post: 10-15-2009, 05:23 AM
  4. Look what we made today!
    By 737NUT in forum My Cockpit Update
    Replies: 4
    Last Post: 10-25-2007, 08:12 AM
  5. Well, I made the leap.
    By jmig in forum My Cockpit Update
    Replies: 5
    Last Post: 07-16-2007, 05:25 PM