Results 1 to 7 of 7
-
11-30-2010, 12:26 AM #1
- Join Date
- Aug 2008
- Location
- USA (Williamsburg,Virginia)
- Posts
- 36
Problem with DVATX using SIM-AVIONICS
Hi All -
I am having a problem getting DVATX to work with SIM-A. All works fine when using the default FSX 737 MCP. However I cannot get my motorized throttles to work using SIM-A. I did modify the ini defining SIMAVIONICS=1. DVATX connects with FSUIPC OK but the A/T stays disconnected. I am using the CPFlight MCP737PRO with SIM-A. The MCP module is running on the SIM-A server which is a separate computer from FSX.
Any other SIM-A users out there using DVATX? Any ideas on this would be much appreciated.
Fred K
-
11-30-2010, 08:37 PM #2
- Join Date
- Aug 2007
- Location
- Australia
- Posts
- 86
Re: Problem with DVATX using SIM-AVIONICS
Hi Fred,
I have the exact same setup. To setup DVATX you not only need to define SIMAVIONICS=1, but also define the THRUSTREF value in the dvatx.ini file. This offset must equal the offset you define for the THRUST_REF_MODE= value in the sim-a FSUIPC_IO.ini file. Additionally, in the FSUIPC_IO.ini file you need to define offsets for COMMANDED_THROTTLE_L_POSITION= and COMMANDED_THROTTLE_R_POSITION= and match these offsets with the servo offsets in the dvatx.ini file..
Hope this helps.
Cheers
Diego
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Dislikes
-
11-30-2010, 11:26 PM #3
- Join Date
- Aug 2008
- Location
- USA (Williamsburg,Virginia)
- Posts
- 36
Re: Problem with DVATX using SIM-AVIONICS
Hi Diego -
Many thanks for your response. I implemented the offset references in the FSUIPC_IO ini and all works like a dream! I am very impressed with how DVATX operates!
Very best regards,
Fred
-
12-06-2010, 07:04 AM #4
- Join Date
- Jan 2007
- Location
- Spain
- Posts
- 146
Re: Problem with DVATX using SIM-AVIONICS
Hi Diego,
could you please tell me where i can donwload DVATX?
tks
Peter
-
12-06-2010, 11:39 AM #5
- Join Date
- Aug 2008
- Location
- USA (Williamsburg,Virginia)
- Posts
- 36
Re: Problem with DVATX using SIM-AVIONICS
Peter -
Go to Downloads->Administrative->DVATX.
Fred
-
12-11-2010, 08:03 AM #6
- Join Date
- Jan 2007
- Location
- Spain
- Posts
- 146
Re: Problem with DVATX using SIM-AVIONICS
Tks,
I have given up trying to get the levers to move in any sensible manner wiht the normal Phidget set up, so will give this one a try
just to confirm, do i need to run ANY phidget software programmes at all with DVATX?
And would DVATX work with the following inputs, as this is how its been connected here
81818 (8/8/
DIG IN
0 ENGINE 1 CUTOFF
1 ENGINE 2 CUTOFF
2 PARKING BRAKE LEVER
3 TOGA
4 AT DISENGAGE
DIG OUT
0 PARKING BRAKE
1 NAVIGATION LIGHT
ANALOG IN
0
1
2
ENG 2 REVERSE
ENG 1 REVERSE
4 SPOILER HANDLE
5 ENG 1 THRUST
6 ENG 2 THRUST
7 FLAPS
77219 (0/0/4)
DIGITAL OUT
0 ACTIVATE THROTTLES
1 ACTIVATE SPOILER HANDLES
2 TRIM UP
3 TRIM DOWN
88658 (SERVOS)
0 THROTTLE LEVER ENG 1
1 THROTTLE LEVER ENG 2
2 SPOILER LEVER
3 TRIM WHEEL
Tks for any help
Peter
-
12-11-2010, 11:56 AM #7
- Join Date
- Aug 2008
- Location
- USA (Williamsburg,Virginia)
- Posts
- 36
Re: Problem with DVATX using SIM-AVIONICS
DVATX works independently of the Phidgets software. Whichever one you execute first will grab the Phidgets main board to the exclusion of the other. So you need only to launch DVATX. There are offset entries that can be modified in the DVATX ini. The software is essentially plug-and-play. Very little modification of the ini is required unless you have a very special case regarding the offsets you are using. Be sure the airlerons offset is set to 0 otherwise you will have uncontrolled flight.
Fred K
Similar Threads
-
DVATX with PHIDGETS DC motor - please help me
By neuman5022 in forum Phidgets Interface & Alan Dyers' FS2PhidgetReplies: 0Last Post: 04-08-2011, 12:04 AM -
About DVATX
By oal331 in forum FS2Phidget UsersReplies: 2Last Post: 01-17-2011, 05:27 PM -
A/T Airspeed Target Problem Using DVATX with SIM-A
By FredK in forum FS2Phidget UsersReplies: 1Last Post: 12-21-2010, 10:53 AM -
Problem Using DVATX with Phidgets
By FredK in forum Phidgets & Cockpit Simulator BuilderReplies: 8Last Post: 05-16-2010, 11:39 PM -
Avionics Master Switch vs. Avionics Switch???
By Tomlin in forum I/O Interfacing Hardware and SoftwareReplies: 4Last Post: 08-08-2008, 09:28 AM
Beautiful Womans in your town for night
B_34 TOGA takeoff