Results 1 to 7 of 7
  1. #1
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Saskatchewan,Canada
    Posts
    226
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Start valve lights?

    I have the start valve lights working on the LED64 card. They come on with the start switch and go out when the switch is released.

    OK,, that works , but I was wondering about the primary pump lights. They should come on when the start switch is pressed ( like the start valve lights) but they should go out about 2 sec or so before the Start switch is released and the valve lights go out.
    ( this is for a Convair turboprop)

    Is there a way I can use the same FS variable (engine start switch) for the primary pump lights BUT put a delay of a couple seconds on the valve lights or speed up the shut off of the pump lights. Have the pump light go out a couple of sec before the start switch is released ??

    Thanks !

  2. #2
    builder
    Join Date
    Jan 2007
    Location
    Texas
    Posts
    582
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    Did you try the timer component?

  3. #3
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Saskatchewan,Canada
    Posts
    226
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    Thanks for the reply.

    I just nticed I still have .18 so I will install .21 and give it a try,, thanks.

  4. #4
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Saskatchewan,Canada
    Posts
    226
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    OK,, i got the timer to turn the light on with a delay but I can't figure out how to get the light to turn off before the start switch is turned of??

    The start switch is held on for 8 sec. The primary pump light should come on when the start switch is engaged and it should turn off approx. 1 or 2 sec before the start switch is disengaged.

    Could I use the timer function to turn the led off after 7 0r 8 seconds,, even with the starter switch still pressed??

    Thanks in advance.
    brian.

  5. #5
    builder
    Join Date
    Jan 2007
    Location
    Texas
    Posts
    582
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    Another approach - instead of using a timer, alternative might be to use engine rpm to turn lights on and off - with start switch engaged.
    i.e. Use range of engine rpm in conjunction with start switch state.

    Is start switch magnetically-held or is switch disengaged manually?
    Last edited by CocnutAir; 01-09-2011 at 06:45 PM.

  6. #6
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Saskatchewan,Canada
    Posts
    226
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    Sounds like a good idea,, to use rpm ! I will give it a try.

    The start switch is held down maually. The primary pump light comes on for a few seconds during the time the start switch is engaged as a test function for the primary fuel pump. If that light doesn't come on,, start sequence is aborted because fuel will not be adequate for light up.

    Thanks again!! I will let you know how it works.

    P.S. Just thought of something. I will use an output for the start switch and an output for rpm on the circuit or else the light will come on every time I reduce power in flight??

  7. #7
    builder
    Join Date
    Jan 2007
    Location
    Texas
    Posts
    582
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Start valve lights?

    As this is fuel pump, how about using fuel flow instead of engine rpm? There is an offset for fuel flow.

Similar Threads

  1. Update 474, Problem with start valve open and flightdirector
    By FlightsimBerlin in forum PM Boeing GC
    Replies: 5
    Last Post: 09-04-2010, 01:37 PM
  2. Start valve open
    By Spyy in forum PM Boeing GC
    Replies: 4
    Last Post: 11-03-2009, 02:36 PM
  3. Fuel cutoff switch/selector valve
    By Prarie Boy in forum General Aviation (GA) Builder Disccusion
    Replies: 5
    Last Post: 10-31-2009, 02:44 PM
  4. Valve annunicators Dim/Bright question - again.
    By touwersl in forum PMSystems
    Replies: 10
    Last Post: 01-11-2008, 01:08 PM
  5. need help on making outflow valve gauge...
    By ruslandemon88 in forum General Builder Questions All Aircraft Types
    Replies: 12
    Last Post: 09-20-2007, 11:21 PM