Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15
  1. #11
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2010
    Location
    Chicago, USA
    Posts
    9
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Need Help Getting My FSBUS NG I/O Going Again..

    Folks....I have some GOOD news and then BAD news....first the GOOD news...

    I managed to get my FSKey Classic III up and running thanks to all your help...

    Now the BAD news....I think I cooked the FSCOM III as I accidently hooked up 12V from PC to it instead of the 5V !! The two PIC's were hot and I can get nothing to work now !!!

    Can I rescue the FSCOM Classic III ? If I replace the 2 PIC's and re-program would that do it or have I damaged other components on the FSCOM board ?

    Any advice would be very appreciated ?

    Thanks...JB

  2. #12
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Netherlands
    Posts
    201
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Need Help Getting My FSBUS NG I/O Going Again..

    Quote Originally Posted by JBRoberts View Post
    Folks....I have some GOOD news and then BAD news....first the GOOD news...

    I managed to get my FSKey Classic III up and running thanks to all your help...

    Now the BAD news....I think I cooked the FSCOM III as I accidently hooked up 12V from PC to it instead of the 5V !! The two PIC's were hot and I can get nothing to work now !!!

    Can I rescue the FSCOM Classic III ? If I replace the 2 PIC's and re-program would that do it or have I damaged other components on the FSCOM board ?



    Any advice would be very appreciated ?

    Thanks...JB

    HI JB

    Just for sure, the you mean the NE555 and the MAX232 ?

    If yes you can replace them, no programming needed because they are ordinairy ICīs.

    Jan

  3. #13
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2010
    Location
    Chicago, USA
    Posts
    9
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Need Help Getting My FSBUS NG I/O Going Again..

    Hi Jan...

    There are 2 PIC's on the FSCOM...one is the MAX232 but the other has the following written on top:

    4312FFK
    SN74HC04N

    Do you think this 4312 will need special programming ?

    Also, do you think I could have damaged any other parts on the FSCOM with the 12 V ?

    Many thanks...JB

  4. #14
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Netherlands
    Posts
    201
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Need Help Getting My FSBUS NG I/O Going Again..

    Quote Originally Posted by JBRoberts View Post
    Hi Jan...

    There are 2 PIC's on the FSCOM...one is the MAX232 but the other has the following written on top:

    4312FFK
    SN74HC04N

    Do you think this 4312 will need special programming ?

    Also, do you think I could have damaged any other parts on the FSCOM with the 12 V ?

    Many thanks...JB

    JB

    Then you have the FSCOM NG !!!
    You must give me (us) the correct info if you want help, it's all in the manuals.
    The 74HC04N is just an ordonairy IC, will cost you a few $ cents.
    No programming needed.

    And yes, there can be more damage, i.e. the transistor BC558, change that as well.


    Jan

  5. #15
    500+ This must be a daytime job



    Join Date
    Jan 2007
    Location
    NEW ZEALAND
    Posts
    899
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Need Help Getting My FSBUS NG I/O Going Again..

    hi,
    D1 if used will also have to be replaced.I dont use Fsbus now but did what you did.Fscom was fixable.Also be prepared to replace other chips on other boards if they were plugged in at the time.If i remember rightly
    the 8535 suffered some damage on the Analogue inputs and had to replace it.
    Les

  6. #16

  7. #17
    New Member
    Join Date
    Feb 2017
    Location
    virginia
    Posts
    2
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Search Pretty Girls from your town for night - Authentic Maidens


  8. #18
    New Member
    Join Date
    Jan 2011
    Location
    -38
    Posts
    4
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Pretty Girls in your city for night - Actual Girls


Page 2 of 2 FirstFirst 12

Similar Threads

  1. Fsbus CDK
    By flyandre in forum General Builder Questions All Aircraft Types
    Replies: 4
    Last Post: 12-27-2014, 12:58 PM
  2. Fsbus ng io
    By Davral in forum I/O Interfacing Hardware and Software
    Replies: 0
    Last Post: 01-10-2009, 10:38 PM
  3. Fsbus 2.4.3
    By Anderson/SBSP in forum I/O Interfacing Hardware and Software
    Replies: 9
    Last Post: 11-30-2008, 04:25 PM
  4. Fsbus
    By 388TH_A in forum I/O Interfacing Hardware and Software
    Replies: 3
    Last Post: 11-16-2008, 05:15 PM
  5. Help FSBUS
    By cesarfsim in forum I/O Interfacing Hardware and Software
    Replies: 2
    Last Post: 10-26-2008, 02:23 PM