Results 1 to 5 of 5
Thread: 727 Mip Dimensions
-
12-04-2008, 02:57 AM #1
- Join Date
- Sep 2007
- Location
- Perth WA
- Posts
- 102
727 Mip Dimensions
Hi Guys,
I have a friend of mine who would like to build a 727 cockpit. Does anyone know where i can find dimensions or drawings for a 727 cockpit.
Cheers
-
12-04-2008, 09:22 AM #2
Hey there.. If I am not mistaken, the dimensions of the 727, are identical to the dimensions of the 737.
Trev________________________
Trevor Hale
-
12-04-2008, 10:15 AM #3
Not quite the same as a 737
I don't have any drawings but the size and shapes are different. The "Glass" MIP is taller and has angles where the -200 advanced has more angles. There are a couple of good picture over at APHS that show it.I do not know if there is a difference between the -100 and -200. I would think the interior shell would be very close to the size of the 737. The first pic is the -200 and the second the glass one.
Rodney -
Real 727-200 pit
Last Flown as N392PA
FS9
-
12-04-2008, 10:19 AM #4
Yes, they are. It's the same fuselage section. Same windows and windscreen, same overhead (main) dimensions and mounting, etc.
The panel is 60" wide, or 5'. Height varies greatly with curves in different areas along the top edge. It's not as cleanly designed as the NG panel. It's a lot like a 737-200 panel. Or I should say the -200 panel is a lot like the 727 panel. And nearly every one is different. You can't build an incorrect MIP for the 727 unless you are modeling a specific airline configuration.
The glareshield and sidewalls are quite a bit different though. I don't know of any dimensions available for the cockpit. I based mine on the 737 for the structure and used photos for the interior. Mine has a couple of errors due to not enough, or late-coming information when it was too late to change anything without a total rework.
If your friend can get ahold of just one instrument panel section he can extrapolate the rest of the panel. Most panels are in 10 sections, but some like mine are only eight sections. Depends upon the age of the bird and the customer.
You can pick up an entire empty 727 instrument panel for around $300-$400. Saves a lot of labor. There are a LOT of holes to cut not only for instruments, but for half a bazillion indicator lamps, buttons, and switches too.
If your friend's time is worth more than the above, it's best to just buy the panel and be done with it. If however, your friend enjoys torture and other mayhem, he can build it himself.
Real panels are relatively cheap compared to aftermarket panels for the 737NG. In fact, dirt cheap. Did I say they are the real panels from the aircraft? Built in lighting, no extra charge. Switches and indicators included and ready to interface into the sim. Some with more hair-pulling and cussing than others, but all doable.
I haven't found anything you can't buy for a 727 except interior trim. That's pretty scarce, but not impossible to build himself.Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
12-10-2008, 06:27 AM #5
- Join Date
- Sep 2007
- Location
- Perth WA
- Posts
- 102
Thankyou for the reply's, i have passed on all your comments and kindly pointed him to the forum.
Cheers
Clint
Similar Threads
-
Help with CRJ dimensions
By BlackWidow in forum Where to Start Building a Home CockpitReplies: 10Last Post: 02-20-2016, 05:55 AM -
FMC Dimensions?
By DanTheSasquatch in forum Cockpit Parts and Motion PlatformsReplies: 1Last Post: 06-08-2011, 06:48 PM -
Dimensions
By Mac in forum Cockpit Outside VisualizationReplies: 6Last Post: 09-12-2008, 01:53 AM -
744 TQ dimensions
By Bobgraag in forum Where to Start Building a Home CockpitReplies: 1Last Post: 04-05-2008, 09:02 AM -
In need of some dimensions 777
By blind0wl in forum Welcome to MyCockpit New here? Introduce Yourself!Replies: 3Last Post: 01-02-2008, 10:10 AM
Pretty Girls from your city for night
Generic Analog Gauges