Results 1 to 9 of 9
  1. #1
    25+ Posting Member
    Join Date
    Aug 2008
    Location
    USA
    Posts
    64
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Panels with electronics

    Hi,

    Potentially a stupid question: I am trying to find vendors that sell A320 panels with electronic components including any PCB needed. I am not sure if CockpitSonic does that in their hardware option. Do you guys know if they do, and if there are other vendors that do so such that the "only" work that I would have to do is to solder all the components in place?
    Thanks,

    Boaz
    KSEA
    Lose money - ask me how.

  2. #2
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    927
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  3. #3
    25+ Posting Member
    Join Date
    Aug 2008
    Location
    USA
    Posts
    64
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Thanks for the reply. What I am not sure about is whether FDS have options where you can get the PCB and all needed components for self-soldering. Do you know if that is the case?
    Thanks,

    Boaz
    KSEA
    Lose money - ask me how.

  4. #4
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    927
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    FDS sells the panels (backlighted) and all the hardware ( SWITCHES ROTARIES ANNUNCIATORS ETC) which are needed for each panel.

    What do you mean by PCB?.... Interfacing cards?

    There is no pcb behind panels switches, rotaries, etc, wires have to go from there to the interfacing boards
    They have little PCB's on annunciators to avoid burning the Leds, that's about it.
    And all the plug and play devices like MCP EFIS Radios do not need any "soldering" they are just plugged in.
    JP
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  5. Thanks PittsburghLever thanked for this post
  6. #5
    300+ Forum Addict



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    487
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Right Boaz, it would be nice to get real PCBs for this stuff, it would make installation so much cleaner, and a lot more reliable IMHO. I know some of the guys on the OC team have made PCBs for the A320 glare, but not real production runs. I had emailed Angel and Louis over there a few times, never got anything firm going on getting panels or Gerber files

    Also, due to the physical and mechanical differences between components any given PCB would almost need to be paired with a built-to-match panel, since mounting hole sizes, etc vary greatly. I designed PCBs for my A320 glare panels but did not have them built due to cost.

    BuddyM

  7. Thanks PittsburghLever thanked for this post
  8. #6
    500+ This must be a daytime job ian@737ng.co.uk's Avatar
    Join Date
    Jan 2006
    Location
    Oswestry, Shropshire
    Posts
    604
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    hi guys.........
    veroboard - 'the cheap alternative'
    i'm building my own circuit boards on this. quite good stuff really. can be cut and trimmed to just about any shape and size.
    one side has a copper strips running along it to which you solder your components and cut
    where needed.
    most components have a pin pitch of 1/10" (or multiple). this is punched out at 1/10" so fitting the bits to it is a breeze.
    here's an example
    http://www.737ng.co.uk/project23.jpg
    hope that helps you out.
    regards ... ian
    Mr. Ian. P. Sissons is hereby recognised as an Honorary Flight Sim Captain following his passing in February 2016. This is in recognition for his commitment to Flight Simulation.

    www.mycockpit.org Featured Builder August 2008 www.737ng.co.uk
    FS9/PROSIM737/CPFLIGHT/Lots of BU0836X's and a Beer Fridge

  9. #7
    25+ Posting Member
    Join Date
    Aug 2008
    Location
    USA
    Posts
    64
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Just a follow-up question (revealing my ignorance when it comes to cockpit building)

    Quote Originally Posted by Jackpilot View Post
    There is no pcb behind panels switches, rotaries, etc, wires have to go from there to the interfacing boards
    So, the panels you'd buy have means of fastening LEDs, switches etc on the panel itself?
    Thanks,

    Boaz
    KSEA
    Lose money - ask me how.

  10. #8
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    336
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Yeah, there are three main parts to the panel, the lightplate (the fancy bit that lights up) the back lighting PCB that has the LED/bulbs for the panel illumination, normally these attach to the light plate via screws and and the backplate that is normally 1.5mm aluminium, things like rotarys, pots and switches bolt to the backplate then you just connect there outputs to whatever interface board you are using, the only time you will need an additional PCB really is for attaching 7 segment LED displays but that can be done without.

  11. #9
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    927
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Panels with electronics

    Usually there is a backer panel, plastic or metal on which you install the switches etc in the ready made holes.



    Then you put the panel itself over the assembly.



    Then you place the assembly where it is supposed to go, (MIP Overhead frame' pedestal frame...)These on the picture are backlightable panels which means that the backer panel is transparent where the panel legends are in order to be able to put a light source behind

    New generation backlighted panels (IBL for FDS) include the little lights in the panel itself and the backer panel can be metal.



    As for the leds they are to be contained in annunciators which you slide in the proper openings of the panels.



    Really obvious when you have it all in front of you.
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  12. Thanks PittsburghLever thanked for this post

Similar Threads

  1. Some electronics help needed!
    By Jordan Farmer in forum Interfacing Real Aviation Parts
    Replies: 5
    Last Post: 01-30-2011, 09:27 PM
  2. Learn (some) Electronics HERE: Electronics simulator (freeware)
    By Hessel Oosten in forum General Aviation (GA) Builder Disccusion
    Replies: 1
    Last Post: 10-02-2010, 01:05 PM
  3. Electronics Help!
    By Geremy Britton in forum General Builder Questions All Aircraft Types
    Replies: 3
    Last Post: 08-21-2007, 06:25 PM
  4. Electronics
    By droddis in forum Where to Start Building a Home Cockpit
    Replies: 6
    Last Post: 06-29-2007, 09:23 AM
  5. B747-400 cockpit panels and associated electronics
    By cheryl88 in forum Where to Start Building a Home Cockpit
    Replies: 3
    Last Post: 04-24-2007, 10:19 PM