PM system and FSbus

[mpl330]

Hi gents,

could any of you get in touch with the Symulatory Team (Jakub or Marek) recently ?

I am currently left with some additional hardware I bought (Fire Panel, Six Packs, Landing Gear), without any ideas/indications about where to plug it to the FSCOM board and - above all - without the proper .fb2 config file ...

I am a person of good will, but good will isn't enough, and I have no idea about where to begin !!!

So this is definitely a mayday-mayday-mayday ...

Help !

Hi,

I will email you what I have...
Between us all we can hopefully sort these issues out - I am stuck on the OH at the moment, got the Pedestal, throttle and CDU working so far, not tried the MCP, EFIS and MIP yet...

Not sure where the Symulatory guys are at the moment - last time there was a delay in getting a response from them they said they had been to Australia...

Regards
Mike

[eudoniga]

Thank you guys ...

A working Symulatory setup would surely be amongst the most desidered Xmas presents !!!



Eugenio

[alfsky]

Hello Peter,

1-The fsbus version is the classic one (version 2.2.0.1)
2-THe overhead from poldragonet is a plug and play device but unfortunately, there are many dummy switches and cadrants. You will find below the instructions from them. the internet link is:
www.symulatory.com

Hello.

Dummy switches on OVHD panel is only wheel well light (most right on light panel) and temperature selector on air condition pannel.
Jakub always sending information about this, with additional information. This switches can be also connected (on special request) but required additional controler (same for wippers, engine start selector,alt horn cutout, and presuization mode selector). This controler in standard is included in AFT OVHD pannel, but everybody can order it without AFT OVHD panel.
My english is not perfect, but I think better world will be "few dummy switches" then "many".

I'm not a symulatory.com member!!! I'm private home cockpit builder.
From time to time I helping them with some translation, also I make design of electronic part for OVHD/AFT OVHD panel.
Attached by jean-louis file was part of my PRIVATE e-mail for him.
I was trying explain them how to make basic test for OVHD.
From time to time clients with no basic technical knowlage has problem with assembly. Everybody on this forum knows that cocpit biulders should be a little IT/electronic specialist Everybody know about troubles with PM software.

Yesterday I was in Warszawa (capital city). My friend bought few months ago
Attitude indicator, Digital altimeter, and Indicated airspeed from flightillusion.
Attitude indicator doesn't work at all, altimeter has broken display.
They don't respond on e-mail, don't recive package with part's send for replacment
As I remember Poldragonet answer on all recived e-mails.
If anybody has problem with communication please let me know, I can forward message to Poldragonet.
Last time one client (from italy) has problem with FMC screen (standard PSONE), but he send it and has been replaced.

It's true I was in Australia this summer. Poldragonet has client with no experience with simulators. He could't find anybody for help on his place, so ask me about help. It was my private trip.
Last week I was in South France at my friend.
He also has own home cockpit. Most parts is from Poldragonet, and it working ok.
Of course there is still some problem with software (YES PM!!).
Anybody can make independent pressure selector on CPT/FO side?
What about STD pressure button? It works fine, we have nice STD indication on GC but pressure is not set for 29.92. Why? And many many more bug like this.

Best regards
Marek

[jrphcien]

hello again guys !

1- Marek, as you can read, my english is not my first language.......the OVH from poldragonet is a good products but yes, i am more a pilot than a computer fan !
2-i finally got how to change assignations with the fsbus router: first as stated by Marek, he send his personal fsif.ini and ovh file and while most of the assignations were ok, l did have to change values for lights and switches and then it worked better.
3- for Mike: i would suggest to verifiy the assignation of each light switche using the key test/dod light test function and their appropriate link to either PM system or any newer logic files. Doing that i did resolve most of my problems. Download from cp flight the mcpex1 op manual for PMsystem ( http://www.cpflight.com/sito/downloads/downloads.asp ) you will find all value for PM systems, the you can write the corresponding fsbus value (it become a paper reference....very useful...)
This thread was not to disregard any products, but to try to solve problems when we spend a few thousands boxes on hardware.....
Finally, i really appreciate you time and contribution to answer this message

[pinosoft]

Hi to all, anyone can send me the fsbus.txt for use with Poldragonet overhead and Pmsystem?

Thank you in advance...

Pino

[airbus319]

PM me your email address and I'll send you my Overhead FSbus file.

A word of warning though they are not all built and wired the same so you may have a mission on your hands to get it working exactly as it should.

Jakub from symulatory usually keeps all the config files so if yours was pre-built and wired by symulatory then he will probably have a copy of it.

Dave

[alfsky]

Hi to all, anyone can send me the fsbus.txt for use with Poldragonet overhead and Pmsystem?

Thank you in advance...

Pino

DId You ask at biuro (at) symulatory dot com ??

[pinosoft]

DId You ask at biuro (at) symulatory dot com ??

Yes, and I have solved!, thank you very much to Jakub!

The Overhead work very well now.

Thanks to all.

Pino

[Efe Cem Elci]

Do you mind sharing with us or putting it up in the files section? That way we can link to it here and others who need it later and happen upon this thread will also find a solution.

[alfsky]

There is 4 diferent version of config depend on particular configuration.
With or without AFT OVHD, with or without additional controler for not supported switches like Whell weel, temperature selector, wipers etc.
Correct files are always included in package or send to customers.
This files belongs to symulatory.com as a part of hardware.
Can't be shared for public. If You didn't recived it with OVHD , You should contact with biuro (at) symulatory dot com.