Page 3 of 3 FirstFirst 123
Results 21 to 25 of 25
  1. #21
    300+ Forum Addict nax228's Avatar
    Join Date
    Oct 2008
    Location
    Oslo
    Posts
    316
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Display bezels 737

    nice nice.... nice enough to buy. Do you sell?

  2. #22
    150+ Forum Groupie
    Join Date
    Jul 2008
    Location
    Belgium
    Posts
    279
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Display bezels 737

    Yes I can make them for you. Just sent me a PM.

    Regards, Wendy

  3. #23
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Display bezels 737

    Hi Wendy,
    You could halve your work by using 6mm PVC sheet! These bezels take me about 12 minutes to machine, I remove the shine with 400 wet and dry, clean with prepsol and paint then paint them with epoxy enamel. This is about 20 minutes for each piece, the bottom strip with the hinge is a seperate piece which is a 5 minute cut. I intend to mount my monitor control strips under the hinged piece, when the LCD monitors are removed from there casings the control PCB and buttons come out aswel and it is easy to relocate, this solves the issue of adjusting monitors easily!!

    Cheers Gwyn
    www.aerosimsolutions.com.au
    Last edited by Westozy; 11-10-2010 at 07:54 PM.

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  4. #24
    150+ Forum Groupie


    steveeverson's Avatar
    Join Date
    Nov 2007
    Location
    Lancashire UK
    Posts
    209
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Display bezels 737

    Hi everyone,
    Just wondered if anyone would be willing to let me have a copy of the GCode or LCam file so I can make my own- i have just bought a small 300x400mm CNC and am running mach 3. - I quite understand if you dont want to part with the code as I know it takes a lot of work but if you can help me out that would be great.
    cheers
    Steve

    ps otherwise I would quite happily buy some Wendy / Gwyn
    Last edited by steveeverson; 11-10-2010 at 08:48 PM. Reason: added ps note
    another bedroom boeing.....

  5. #25
    150+ Forum Groupie
    Join Date
    Jul 2008
    Location
    Belgium
    Posts
    279
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Display bezels 737

    Hey Gwyn,

    Well that's also the way I do it. Except I use 9 mm so that they are sunking into the MIP (3 mm taken away on the back of the bezel). That way you will see 6 mm. on top of the MIP but but on the inside they are 9 mm. which brings them closer to the monitor.

    @Steve
    Sent you a PM

Page 3 of 3 FirstFirst 123

Similar Threads

  1. Where can i get stand by bezels for 737ng
    By BishBash in forum General Builder Questions All Aircraft Types
    Replies: 1
    Last Post: 02-07-2010, 08:10 AM
  2. STD to display
    By SteveClarke in forum PM General Q & A
    Replies: 8
    Last Post: 02-22-2007, 05:32 PM
  3. Re: possible bug in GC (ND display) ??
    By John Ebbers in forum PM General Q & A
    Replies: 0
    Last Post: 02-04-2006, 03:58 AM
  4. possible bug in GC (ND display) ??
    By John Ebbers in forum PM General Q & A
    Replies: 3
    Last Post: 01-18-2006, 01:06 PM
  5. FCU FD Display
    By Peter Martin in forum PM General Q & A
    Replies: 1
    Last Post: 01-08-2006, 08:34 AM

Tags for this Thread