A320 FMGS B46

[imported_Suggy]

If you are using FDS boards, have you used IITcreator for the switch and led assignments?

I have very recently moved from a well known A320 software suite to Jeehell which required a complete reassignment exercise including using IITcreator.
Initially I had a problem as Gen1 and Gen2 would not come on line although all the start-up procedure was correct.

To cut a long story short, I found that the problem was my IDG switches and how they were assigned (up/down/toggle) in IITcreator. The physical attributes of the switches were different to all my other switches. What was happening, because of the way the switch was configured, the IDGs must have been disconnecting straight after powering up the aircraft.

Initially I thought it was a software problem but dismissed that as the start sequence was fine if I used the graphical software without starting my hardware boards.

I'm finding that any errors in your hardware setup will cause problems since the software's logic is excellent!

The IITcreator has a couple of bugs in it e.g. the IDS 2 and 3 Allign leds are the wrong way round...

Regards,
Darren Sugden

[anzabon]

Hello Jean-Luc,

thank you for your recommendation to check the fire handles... since the APU fire handle assignment is inverted here and one of the wire had lost contact to the micro switch the system thought APU fire handle was active. So that has been the reason for the failures.
Thank you very much for your help!

Only the APU still doesn't run down after switching off on the OVHD. It simply continues running...

Kind regards,
Bon

[corco19]

Hello Jean-Luc,

thank you for your recommendation to check the fire handles... since the APU fire handle assignment is inverted here and one of the wire had lost contact to the micro switch the system thought APU fire handle was active. So that has been the reason for the failures.
Thank you very much for your help!

Only the APU still doesn't run down after switching off on the OVHD. It simply continues running...

Kind regards,
Bon

I have checked that, and the sames happens to me. Once I have APU running and engines started, when I try to stop the APU, it remains still with AVAIL on.

I haven´t investigated that yet, because I am just starting and performing some test.

[jeehell]

The APU runs for about 2 minutes after APU bleed has been used (even for a fraction of seconds) as a cooldown period. It will stop automatically when this cooldwon phase is over (and master SW was initially pushed of course).

[Leonidas]

Hi
Anyone using ATC-PRO/X? I can't get Clearance at the beginning, even though I tune proper freq. All others freq. operate properly (ATIS, Depart etc).
This is not off topic cos I've read in a ATC-PRO/X forum discussion that this Clearance doesn't work for some addons and I hope JeeHell is not one of them.
Thank you

[Leonidas]

Hi
The volume of JeeHell Sound application drops to 5-10% in Windows Sound Mixer. This happens 2-3 times every flight time. Anyone with same issue?

[fisfro]

Hi
The volume of JeeHell Sound application drops to 5-10% in Windows Sound Mixer. This happens 2-3 times every flight time. Anyone with same issue?

Hello,

I have a similar sound problem. The volume drops after position changes in p3d or pause activation.reseting the flight in p3d will set the default volume....


Robert

[Dan320]

Hey Guys

Have you tried switching the position in "sound" settings "communications" tab to "do nothing"?

https://superuser.com/questions/4500...ndows-7-64-bit

Best regards

Daniel

Hello,

I have a similar sound problem. The volume drops after position changes in p3d or pause activation.reseting the flight in p3d will set the default volume....


Robert

[jeehell]

Hello,

B47 is out, check :
http://www.mycockpit.org/forums/show...867#post166867

JL