A320 FMGS B45

[Firefly77]

Hi JL, thanks for qiuck reply! Strange, I did a complete fresh install from the link above and did not get any autoupdater window ?? How else I can update it ? BR
Mic

[OmniAtlas]

Ben: did you try with admin rights?


JL

Tried reinstalling again with admin rights, and also running the updater byitself with admin, I still get the same 'failed once', 'failed twice' error message.

[Fritz]

With the update to version 45.3 beta my ACC Press gauge is working again.
I made a new assignment in IIT Creator for the Passenger SYS ON Light LED. Haven't seen that is was implemented. However, these lights constantly. The OXYGEN TMR RESET switch on the overhead panel Maintenance is not yet implemented. Is there a another option, or should I delete the assignment again?
Some sound files are corrupted. Have replaced it with files from previous versions.
I am using skalarki TQ Model 2012 with the new profiler. The Trim wheels do not reset to 0° after landing.

[Firefly77]

Hi Jeanluc, maybe you can again have a look into the Intercomm.exe ? I have the most recent version of FMGS installed and also the autoupdater is saying "current version is up to date". However, the intercomm.exe is not saving my settings !

-- My Trimwheels do not reset to 0 after landing as well.

Best regards
Mic

[Leonidas]

Hi
SOUND PROBLEM
After a clean installation there is no FMGS sound, just model's A320 sound. Some times sound.exe doesn't start even though it's in starter.ini. So, I start it by myself, but there is no sound too. Also, Intercom file is 0KB and when I execute it, that message shows up. Any suggestion?

[OmniAtlas]

Hi
SOUND PROBLEM
After a clean installation there is no FMGS sound, just model's A320 sound. Some times sound.exe doesn't start even though it's in starter.ini. So, I start it by myself, but there is no sound too. Also, Intercom file is 0KB and when I execute it, that message shows up. Any suggestion?

I've previously mentioned this to JL -- most likely an updater.exe problem; the solution at this stage would be to backup your intercom.exe from B45.3. Reinstalling and running as administrator brings about the same issue.

[masterp]

Hi JL, in MCDU I can not select between Squawk mode Standby or Mode C.
at startup it blue up both standby and mode C.
I select Mode C however my VATSIM software vPilot not turn to Mode C as previous version of FMGS.
Thanks.

[Miatanet]

Hi JL, in MCDU I can not select between Squawk mode Standby or Mode C.
at startup it blue up both standby and mode C.
I select Mode C however my VATSIM software vPilot not turn to Mode C as previous version of FMGS.
Thanks.

Hi all,

does the Squawk mode selection works with Skalarkis TCAS panel for IVAO. I always need to turn the knob on the IVOA interface. Does someone have that working via the TCAS panel switch?

Thank you for a short feedback.

BR
Stefan

[tuomasho]

Did you update your magnetic variation data? http://www.aero.sors.fr/navaids.html

With the latest update JL the intercom.exe now does not run -- using Windows 10.

Regards,

Ben

Hi,

and thank's for your reply. Tried the old magnetic variation data and new. Doesn't work... Tried many different things and there are some airports runways that works with ils and some doesn't. Example in EFHK rw 04L and 04R doesn't work (when ils is correct in nd plane is about 20m right from the center of rw). But some other rw's at EFHK it works. Example in EFJY it works and some other FSX original airports and as well some of addon airports. But there is also much of airports it doesn't work. Mostly the plane is about 20m to right from the rw, but some occasions it can be to left about 50-100m.


Do anyone have a clue what can cause this/any solution?

-=Tuomas=-

[jeehell]

The issue with ILS and RWYs is due to mis alignment between the navdata from Aerosoft/navigraph and the facilities inside FS/P3D.
To counter that, when compiling the navdata bin files, my soft reads directly the FS/P3D BGL files to correct the navdata with ILS/RWY lat,lon,course.
With P3D V3, now everythign has to be put outside P3D folder, this could be the issue, particularly if your problem is only with addon sceneries.
The problem is also present with Runways which changed QFU, or which were later added, so the original runway naming changed to for example R/L or C.

JL