A320 FMGS B31

[OmniAtlas]

Check out this air.file.
https://www.dropbox.com/s/p7nji1i642...20-cfm56-2.zip
It seems to me that it is included in the B32...
Maybe you have not installed the model again?

Ah that is correct. I have not updated my model since b31. I will try again with the new model.

Perhaps jh can make the installer overwrite our sim objects directory by default? It was unknown to me that there was a new model.

Thank you.

[Stephan Schwarz]

@ToTom: uh, I was not aware that a model change must be done. Thank you for this file!

@OminAtlas: I guess you are right with RAAS I almost forgot that I recently installed it. Anyway, I do reset my altimeter at FL180, but RAAS does not seem to recognize it. Will check it out this evening!

[filippoporcari]

the model update is included in the full installer.
JL reported about the model update in the bug tracker.
cheers
fil

[OmniAtlas]

Tried out the new model, no problems going to FL370 this time; big time problems calculating vertical altitudes at way points coming down (they were left blank for some reason?), but we know that hasn't been modeled correctly yet.

Seems like the new model makes more accurate turns but I will have to do more testing -- we can try a 90 degree turn to ILS approach next time

[OmniAtlas]

@OminAtlas: I guess you are right with RAAS I almost forgot that I recently installed it. Anyway, I do reset my altimeter at FL180, but RAAS does not seem to recognize it. Will check it out this evening!

Are you using the commercial RAAS by FS2Crew or the freeware version?

[ToTom]

Anyway, I do reset my altimeter at FL180, but RAAS does not seem to recognize it. Will check it out this evening!

You need to connect offsets in FMGS with standard offsets in FS or transfer the information directly to the RAAS.

Seems like the new model makes more accurate turns but I will have to do more testing -- we can try a 90 degree turn to ILS approach next time

There is no more changes in the model. Just indicate the PSI...

[Stephan Schwarz]

You need to connect offsets in FMGS with standard offsets in FS or transfer the information directly to the RAAS.

Found a better solution Just deactivated this message in the options tab. I use the commercial version of RAAS.

[Stephan Schwarz]

Here are some additional lines for the aircraft.cfg which enable the Jetway. Maybe someone need this:

[exits]
number_of_exits = 3
exit.0 = 0.4, 40.50, -6.0, 6.0, 0 //openclose rate percent per second, longitudinal, lateral, vertical positions from datum (feet), type (0=Main 1=Cargo 2=Emergency)
exit.1 = 0.4, -23.50, 5.85, 0.0, 1 //openclose rate percent per second, longitudinal, lateral, vertical positions from datum (feet), type (0=Main 1=Cargo 2=Emergency)
exit.2 = 0.4, 29.90, 6.0, 1.0, 2 //openclose rate percent per second, longitudinal, lateral, vertical positions from datum (feet), type (0=Main 1=Cargo 2=Emergency)

[RigoA320]

Hello JH


I have a question.


Can I use only your A 320, or I can from a different software such as Aribuns Extendet A 320 use without interference.
MfG Rigo

[jeehell]

Hello JH


I have a question.


Can I use only your A 320, or I can from a different software such as Aribuns Extendet A 320 use without interference.
MfG Rigo

You can only use the A320 included in my package.


JL