Progamming help with FSBus dll

[John_B]

388TH_A

Is your issue the rotary encoders only counting up regardless of direction of rotation?

(I have had this)


If so there's a better than average change that they are either wired/connected incorrectly or the wrong type of switch is selected in the setup admin. If memory serves I also had to make sure also that one of the pairs the encoder uses has not already been assigned a rotary switch type (ie clear them back to basic toggles then assign em!)

John

[ThomasCaL]

Appreciate you sharing, great forum.Much thanks again. Whipkey

[388TH_A]

ok so Back to where I was my knobs for my com1, com2 etc doesnt matter if you turn them to the left or right it makes the freq count up. And it does this for the FRA and DEC place.

MkFsbusObject(BTP_ROTARY, C_RCOM1DEC, "OID", EventHandler, 29, 5);
MkFsbusObject(BTP_ROTARY, C_RCOM1FRA, "OID", EventHandler, 29, 3);

/*---------------------- COM1 Events ----------------------*/


case FS_COM1FREQUENCY:
Com1Fr = ((10000 + BCD2Int(val)) * 10 + 5) / 25 * 25; // rounded, units: 0.001
FsbusWrite(C_DCOM1, Com1Fr / 10); // to cockpit
break;
case FS_COM1STANDBY:
Com1FrStb = ((10000 + BCD2Int(val)) * 10 + 5) / 25 * 25;
FsbusWrite(C_DCOM1STB, Com1FrStb / 10); // to cockpit
break;
case C_RCOM1DEC:
x = Com1FrStb %1000;
x = x + 25 * val; // in steps of 0.025
if (x > 975) // upper limit: 0.975
x = 0;
else if (x < 0)
x = 975;
Com1FrStb = Com1FrStb / 1000 * 1000 + x; // units: 0.001
FsbusWrite(C_DCOM1STB, Com1FrStb / 10); // truncated to 0.01
x = Int2BCD((Com1FrStb % 100000) / 10); // stripped and truncated to 0.01
FsWrite(FS_COM1STANDBY, x); // to FS
break;
case C_RCOM1FRA:
x = Com1FrStb / 1000; // ahead of dec point
x = x + val; // in steps of 1.000
if (x > 136)
x = 118;
else if (x < 11
x = 136;
Com1FrStb = x * 1000 + (Com1FrStb % 1000);
FsbusWrite(C_DCOM1STB, Com1FrStb / 10);
x = Int2BCD((Com1FrStb % 100000) / 10);
FsWrite(FS_COM1STANDBY, x);
break;
case C_SCOM1SWAP:
if(val==0)
FsWrite (FS_RADIOUSESTBYTOGGLE,0x0; // toggle bit 3 (COM1)
break;
case C_SCOM1TEST:
break;

[388TH_A]

Ill look into that but I know im missing something because at one point in time I had everything working back when before I had to start over

[388TH_A]

So went threw all of the code and looks like theres isnt any doubles of anything for the IDs

[388TH_A]

So I worked on my stuff for a bit and then stopped for yrs and now im working on them again from time to time. So looks like on my IO board some of the connections might be touching for example you can have a switch on 00 but when you flip the switch 00 and 16 will be effected. This is also the same for 32,48 08,24 and 40,56. The other issue I found was I have to go to ever switch and rotary and Define it in the FSBUS Admin screen in the CDK in order for them to work like they should. If I dont then for example the Rotary will only count up. After fixing it, it will then count up and down so there for it was never the C++ like I thought.

Do you guys know of other ways to fix the rotarys with out going to each one and defining them in that Admin screen?

[cotheseest]

Why would an air conditioning company ask hvac techs what problems they are having with their heaters? Strange.