Results 1 to 4 of 4
  1. #1
    150+ Forum Groupie Drewsta's Avatar
    Join Date
    Oct 2007
    Location
    Australia
    Posts
    206
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Buo386X and led pushbuttons?

    Hey guys, I'm not sure wether this question has been done to death but I can't find anything on these particular pushbuttons. Can I connect these pushbuttons with built in Leds to leo Bodnar's Buo386x card.



    blackpushled.jpgI don't need anything fancy to happen, just when push the button once it latches and the led comes on and say the the center fuel pump comes on. Push it again and the led goes out and the center fuel pump goes off. Does anyone know if this is possible with this card? I want to use it on the leveld767 overhead.

    Thanks
    Drewsta

  2. #2
    75+ Posting Member Leo Bodnar's Avatar
    Join Date
    Apr 2008
    Location
    UK
    Posts
    94
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Buo386X and led pushbuttons?

    Hi,
    Yes, connect it as follows:
    +5V -====- [+LED-] -====- B1 -====- [switch] -====- GND
    B1 is a button terminal input and has two wires. +5V and GND are any terminals marked as such on BU0836X.
    Make sure you that you use current limiting resistor (around 300-600 Ohms) in series with the LED if the switch does not have one inside!
    Cheers
    Leo

  3. Thanks Geremy Britton thanked for this post
  4. #3
    150+ Forum Groupie Drewsta's Avatar
    Join Date
    Oct 2007
    Location
    Australia
    Posts
    206
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Buo386X and led pushbuttons?

    Quote Originally Posted by Leo Bodnar View Post
    Hi,
    Yes, connect it as follows:
    +5V -====- [+LED-] -====- B1 -====- [switch] -====- GND
    B1 is a button terminal input and has two wires. +5V and GND are any terminals marked as such on BU0836X.
    Make sure you that you use current limiting resistor (around 300-600 Ohms) in series with the LED if the switch does not have one inside!
    Cheers
    Leo
    Hi Leo, thanks for your reply mate. A couple of questions as I've never used any form of I/O card before. Would you happen to have an easy to follow diagram or be able to point me to one? Also which 5v connection do I use, any one? Can I put some sort of long connector attached to the 5v pin so that i can connect all the leds into the connector that can be connected to the 5v pin? Also I would like to buy more than 1 card, can i use more than 1 card on the sim?

    Thanks for your time
    Drewsta

  5. Thanks Geremy Britton thanked for this post
  6. #4
    150+ Forum Groupie
    Join Date
    Jan 2007
    Location
    Saskatchewan,Canada
    Posts
    226
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Buo386X and led pushbuttons?

    I plan on using 2 or 3 BUO386x cards on a single project and was wondering about giving different names to the cards in WindowsXP game controller ?
    or does fsuipc do that?

    i read in a previous thread that a person could order cards with a custom name. If so, how would I go about that?

    Thanks much .

Similar Threads

  1. Need Garmin GNS430 Style PushButtons
    By k5beason in forum I/O Interfacing Hardware and Software
    Replies: 1
    Last Post: 04-05-2011, 01:14 PM
  2. Buo386X
    By Drewsta in forum I/O Interfacing and Hardware
    Replies: 3
    Last Post: 10-13-2010, 05:17 PM
  3. Illuminated Pushbuttons Question
    By Buddym in forum Cockpit Parts and Motion Platforms
    Replies: 3
    Last Post: 02-24-2009, 12:05 AM
  4. Led Pushbuttons with LevelD 767
    By Drewsta in forum I/O Interfacing Hardware and Software
    Replies: 1
    Last Post: 07-06-2008, 07:24 PM