Results 1 to 6 of 6

Thread: Easier wiring

  1. #1
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Easier wiring

    Was looking at simulator websites, and came across this picture:



    Does anyone know how he wired the wires to the male IDE connector? For example, the blue wire going from the pot has a little light green piece connecting it to the male IDE connector... what is that? And is this the preferred way to wire opencockpit boards?


    PS, original image from Nic's website: http://www.insitesolutions.com.au/737project/

  2. #2
    500+ This must be a daytime job


    Efe Cem Elci's Avatar
    Join Date
    Jan 2008
    Location
    Istanbul, Turkey, Turkey
    Posts
    509
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Lezam View Post
    Was looking at simulator websites, and came across this picture:



    Does anyone know how he wired the wires to the male IDE connector? For example, the blue wire going from the pot has a little light green piece connecting it to the male IDE connector... what is that? And is this the preferred way to wire opencockpit boards?


    PS, original image from Nic's website: http://www.insitesolutions.com.au/737project/
    Well I had noticed this in some other sites but couldn't find those cables either... thanks to you I convinced myself to take another in depth look.

    Here's what I came up with:

    connector
    http://www1.uk.conrad.com/scripts/wg...0&cachedetail=
    and sets:
    http://www1.uk.conrad.com/scripts/wg...0&cachedetail=

    heat-shrink tubing:
    http://www1.uk.conrad.com/scripts/wg...0&cachedetail=

    of course I would suggest a detailed look at these to determine correct size before ordering.

    connector pin troughs (similar)
    http://www1.uk.conrad.com/scripts/wg...0&cachedetail=

  3. #3
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I could be wrong, but looks like he has soldered to the pin and put green shrink tubing on it..

    But could be wrong.
    ________________________
    Trevor Hale

  4. #4
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Would soldering be the best option? I'm still all confused about the most efficient way of wiring, with the possibility of changing inputs later on.

  5. #5
    75+ Posting Member RalphW's Avatar
    Join Date
    Oct 2006
    Location
    London, UK
    Posts
    77
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I use these for switch and LED to Simboard connections.

    http://www.rapidonline.com/largeimag...image=55016701

    For switches solder the open wire ends to the switch and connect other end to simboard. For LEDs, push the LED into the connector and crimp pins onto the open wire ends which you then connect to the simboard. Saves a lot of hassle and time.

    Regards

    Ralph
    Speedbird17

  6. #6
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    With opencockpit IO cards?

Similar Threads

  1. help ref wiring
    By BishBash in forum I/O Interfacing and Hardware
    Replies: 26
    Last Post: 11-03-2010, 07:06 PM
  2. Easier way to I/O?
    By JD_LincsUK in forum I/O Interfacing Hardware and Software
    Replies: 7
    Last Post: 04-09-2010, 08:29 AM
  3. Whats the easier cheaper solution.
    By hamsterboy in forum Pilots Lounge - Let your Hair down
    Replies: 8
    Last Post: 07-23-2009, 04:30 PM
  4. On refelection, the Viking Funeral would have been easier
    By PaulEMB in forum My Cockpit Update
    Replies: 1
    Last Post: 10-18-2008, 05:29 PM
  5. Wiring
    By imported_767300 in forum General Builder Questions All Aircraft Types
    Replies: 10
    Last Post: 06-10-2007, 01:46 PM