Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Making clear knobs with molds

    Working with the excellent tutorial on making your own knobs here:

    http://personales.ya.com/micabina737...es/moldesi.htm

    Does anyone know of an easy alternative to their mold that will make clear knobs, which will then be coated with paint? Something like simknobs did?


  2. #2
    300+ Forum Addict



    Join Date
    Feb 2007
    Location
    California, USA
    Posts
    377
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    The book The Prop Builder's Molding & Casting Handbook by Thurston James covers several approaches to molding and casting. The silicon rubber mold is one of the best because of its accuracy and because it can be reused. There are less expensive approaches, but I don't think they would be any easier.

  3. #3
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I'm just looking for a material to substitute his "Cronodur A + B" that will produce clear knobs to be used with backlighting.

  4. #4
    300+ Forum Addict



    Join Date
    Feb 2007
    Location
    California, USA
    Posts
    377
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Tap Plastics carries various materials. http://www.tapplastics.com/shop/category.php?bid=33&

    Also check Ebay using "casting resins" as search terms.

  5. #5
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks Mike! Just what I needed

  6. #6
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    336
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I use a 2 pak product called DR006 made by Atlas polymers here in the UK with stunning results. even down to having metal inserts encapsulated !!

    But its never simple, I have to spin each knob in a lathe to get the bottom flat and have to apply 4 different layers of paint to get them right.

    When producing a mould from RTV silicone remember to read the datasheet carefully, the stuff i use needs 7 days to cure, if you cast before the silicone has cured you get a nasty reaction between the two, also keep in mind the shrink ratio of whatever resin you use.

    But here are some ive done before






  7. #7
    300+ Forum Addict



    Join Date
    Feb 2007
    Location
    California, USA
    Posts
    377
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Very nice work!

  8. #8
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,883
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Excellent job Phil. I've made clear knobs but, NEVER, got results like yours. Fantastic!!!!

  9. #9
    75+ Posting Member Lezam's Avatar
    Join Date
    Dec 2007
    Location
    New York
    Posts
    84
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thats amazing work Phil! I have a couple of questions for you:

    Where do you get your original knobs, they look extremely realistic.
    What kind of paint do you recommend for the knobs, so they get a textured feel?

  10. #10
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    336
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    OK,

    Basically all Knobs I produce have been master casted from an original part, with the exception of the boeing IRS knob that i have turned down with a lathe, I have spent many months aquiring them.

    I use 4 layers of 2pak acrylic, first coat is white with 30% 2K clear coat mix (this produces a bright wight that light will shine through) then a standard matt black (to avoid light bleed through) then a coat of 2K beige (actually a Lada colour, perfect match!!) finished with a satin lacquer (not really needed but gives a dull finish that wont wear for quite some time). the paint itself is the same stuff you use on your car

Page 1 of 2 12 LastLast

Similar Threads

  1. Please give me clear input Thanks
    By sidney095 in forum Computer Hardware Setup
    Replies: 2
    Last Post: 03-18-2011, 10:06 PM
  2. Making a new 737 MIP from MDF or something better?
    By SAS541 in forum General Builder Questions All Aircraft Types
    Replies: 8
    Last Post: 05-04-2010, 07:04 PM
  3. Knob Molds?
    By Buddym in forum Westozy's Mechanical Engineering
    Replies: 4
    Last Post: 03-20-2010, 12:47 PM
  4. V nav to v speed problem. is there clear solution yet
    By nige in forum PM General Q & A
    Replies: 0
    Last Post: 12-01-2008, 06:10 PM
  5. Making a MCP etc Box
    By Lewis Simmons in forum Cockpit Parts and Motion Platforms
    Replies: 4
    Last Post: 05-05-2008, 12:46 PM