Results 1 to 5 of 5
  1. 02-12-2014, 05:20 PM #1
    pmartin
    pmartin is offline
    25+ Posting Member
    Join Date
    Nov 2008
    Location
    W黵zburg
    Posts
    68
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question APU Procedure stops at "Flap open"

    Hello guys!
    I installed the FS X, the Jeehell-Soft and an configure a throttle and a joystick!
    After this i start the "StarterFSX".
    Everything is working until the position "APU-Start".
    After i start the APU with "APU-Master" after this "APU-Start".
    I see on the SD the APU page. I see the message "Flap open" but the "N" and "EGT" are not starting.

    I hope anyone know the problem why the APU-procedure stops!

    regards
    Peter
    Reply With Quote Reply With Quote
  2. 02-12-2014, 07:02 PM #2
    jeehell
    jeehell is offline
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,652
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: APU Procedure stops at "Flap open"

    Hi,

    You did not pause FSX?

    Regards,
    JL
    Reply With Quote Reply With Quote
  3. 02-13-2014, 01:01 AM #3
    pmartin
    pmartin is offline
    25+ Posting Member
    Join Date
    Nov 2008
    Location
    W黵zburg
    Posts
    68
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: APU Procedure stops at "Flap open"

    hello jl!
    No not paused!
    regards peter
    Reply With Quote Reply With Quote
  4. 02-13-2014, 02:45 AM #4
    OmniAtlas
    OmniAtlas is offline
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: APU Procedure stops at "Flap open"

    Did you start the ab flyby wire exe (can't remember the exact file name)?
    Reply With Quote Reply With Quote
  5. 02-13-2014, 05:44 AM #5
    pmartin
    pmartin is offline
    25+ Posting Member
    Join Date
    Nov 2008
    Location
    W黵zburg
    Posts
    68
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: APU Procedure stops at "Flap open"

    Hello guys!
    I found the problem!
    At first i had to say i installed all Soft (FSX an Jeehell) on one Laptop for a test configuration.
    And the problem of this Laptop is, that i see the last line of the fsx-window not!
    So the cracks know whats happend )
    I forgot to unmark at the FSX config that he "pause" if i leave the fsx window!
    After this my software is working (means the apu starts and the start-button shows "avail" etc.)
    Thanks for helping anyone!
    regards peter
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »