Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    25+ Posting Member
    Join Date
    Feb 2008
    Location
    Jönköping, Sweden
    Posts
    50
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Unhappy CG in Takeoff Ref page of PM 737 CDU

    I hope someone can help me here.

    I have just installed the PM Boeing suite of software and everything is up and running fine.

    I am a little confused however, as the CG figure is empty in the Takeoff Ref page of the CDU. I realise that i need to enter this, but how do i calculate this figure? What figure are other users entering here that are flying the FSX default 737-800?

    Doesn't the PMDG software calculate this figure from FS itself depending on the way the aircraft is loaded?

    How can we do the same for PM?

    Looking forward to any help i can get.

    Thanks.

    Regards
    Benja

  2. #2
    300+ Forum Addict autocadplease's Avatar
    Join Date
    Jan 2008
    Location
    British Columbia, Canada
    Posts
    446
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I use 20% C of G. You can calculate it, but you need all the weights and moments to do it.

  3. Thanks Padraig, SAS541 thanked for this post
  4. #3
    150+ Forum Groupie Padraig's Avatar
    Join Date
    Feb 2008
    Location
    Eire
    Posts
    221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Yes I was wondering that too , I remember when I was using the PMDG 737 with FS2004 it used to calculate it all the time which was great, but with FSX and default 737-800 it didn't do anything. I'l try the 20% too, but do you know the actual formula for the calculations ? because I would like to work it out, as I use loads of different payloads for displacement when flying different routes.

  5. #4
    300+ Forum Addict autocadplease's Avatar
    Join Date
    Jan 2008
    Location
    British Columbia, Canada
    Posts
    446
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    You could just use a load and trim sheet. I cannot find a good one for the 737-800, but there is one at the end of this accident report:

    http://www.bfu-web.de/nn_53140/EN/Pu...tmund_B737.pdf

    To calculated it manually, you need the moments (distance of item from datum) for each of weight - and I don't know where to get those. You could use the ones from the aircraft.cfg? Also, you need the MAC (Mean Aerodynamic Chord) in order to calculate the % MAC - again I don't have that figure either. I'm lots of help, eh!

    Update:

    My 737-800 aircarft.cfg says:
    WEIGHT_AND_BALANCE]
    max_gross_weight = 155500 // (pounds)
    empty_weight = 85710 // (pounds)

    reference_datum_position = 0, 0, 0 // (feet) distance from FlightSim Reference position: (1/4 chord, centerline, waterline)
    empty_weight_CG_position = -9, 0, 0 // (feet) longitudinal, lateral, vertical distance from specified datum

    max_number_of_stations = 50

    station_load.0 = 170.0, 46.3, -1.5, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.1 = 170.0, 46.3, 1.5, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.2 = 510.0, 0.0, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.3 = 1360.0, 33.4, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.4 = 5440.0, 16.1, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.5 = 5440.0, -9.7, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.6 = 4760.0, -28.0, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.7 = 4000.0, 24.7, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)
    station_load.8 = 1000.0, -34.4, 0.0, 0.0 //Weight (lbs), longitudinal, lateral, vertical positions from datum (feet)

    station_name.0 = "Pilot"
    station_name.1 = "Co-Pilot"
    station_name.2 = "Crew"
    station_name.3 = "First Class"
    station_name.4 = "Coach 3-10"
    station_name.5 = "Coach 11-18"
    station_name.6 = "Coach 19-25"
    station_name.7 = "Forward Baggage"
    station_name.8 = "Aft Baggage"

    ;Moments of Inertia
    empty_weight_pitch_MOI = 1600655
    empty_weight_roll_MOI = 588050
    empty_weight_yaw_MOI = 2148751
    empty_weight_coupled_MOI = 0

    So, you can calculate the C of G based on the above, but I don't know how to get the % MAC without the MAC figure.

  6. Thanks SAS541, Padraig thanked for this post
  7. #5
    150+ Forum Groupie Padraig's Avatar
    Join Date
    Feb 2008
    Location
    Eire
    Posts
    221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks alot for this, I will take all this into account later on tonight and try it out. I find that putting in the right CG % helps me for take off period and intial climb. I hate when its not set right, the aircraft does not feel the same. This was a ongoing problem for me since my weight is always different after I calculated the fuel needed for a certain flight I embark on.

    Once again,

    A big thanks

  8. #6
    300+ Forum Addict
    Join Date
    Jan 2007
    Posts
    496
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by autocadplease View Post
    You could just use a load and trim sheet.
    The current CG as a % of MAC is provided in FSUIPC offset 2EF8, as a 64-bit floating point value. You can check it in FSUIPC by going to the Logging tab, right-hand side. Enter 2EF8 as the offset, FLT64 as the type, and check the "FS Window" or "AdvDisplay" option at the bottom.

    There may be a way of getting it displayed elsewhere, via pmSystems perhaps? Or if you are using any GoFlight displays you could use my GFDisplay program.

    Pete

  9. Thanks SAS541, Padraig thanked for this post
  10. #7
    150+ Forum Groupie Padraig's Avatar
    Join Date
    Feb 2008
    Location
    Eire
    Posts
    221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks pete, I have a look now.

  11. #8
    10+ Posting Member BillTee's Avatar
    Join Date
    Dec 2006
    Location
    Cameron Park, California USA
    Posts
    20
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hello Pete,

    I just tried your suggestion from above and got this display; "IPC:2EF8(FLT64)=0.2826" Would that be equal to 28.3% CG of the MAC?

    Best regards,
    Bill Trinidad

  12. #9
    150+ Forum Groupie Padraig's Avatar
    Join Date
    Feb 2008
    Location
    Eire
    Posts
    221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by BillTee View Post
    Hello Pete,

    I just tried your suggestion from above and got this display; "IPC:2EF8(FLT64)=0.2826" Would that be equal to 28.3% CG of the MAC?

    Best regards,
    Bill Trinidad
    I have done what pete said, but I was getting 23.2425 which I gather means 23.2% GG. But I might not be correct. Whats the ZFW your using and fuel on board etc ?

  13. #10
    10+ Posting Member BillTee's Avatar
    Join Date
    Dec 2006
    Location
    Cameron Park, California USA
    Posts
    20
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I didn't note the weights before, so I did another;

    B739 PMDG
    ZFW=128000
    Fuel=20006
    GW=148006

    "IPC:2EF8(FLT64)=0.2450"

    I wonder why my numbers are different

    Bill T.

Page 1 of 2 12 LastLast

Similar Threads

  1. Cleared for takeoff
    By ManuManu in forum Welcome to MyCockpit New here? Introduce Yourself!
    Replies: 4
    Last Post: 04-11-2011, 12:10 PM
  2. CDU: Strange values on my takeoff page
    By Norbert-EDDV in forum PM Boeing FMC/CDU
    Replies: 4
    Last Post: 07-23-2008, 03:53 AM
  3. CG in Takeoff Ref page of PM 737 CDU
    By SAS541 in forum PM General Q & A
    Replies: 11
    Last Post: 04-03-2008, 08:10 PM