Results 1 to 7 of 7

Thread: 3D Printing

  1. #1
    Administrator


    W9XE/Project777's Avatar
    Join Date
    Oct 2005
    Location
    Warrensburg, Missouri
    Posts
    254
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    3D Printing

    With a lot of talk out there about 3D printing and how much prices have come down has anyone thought of making flight sim parts with it? Found a link Store that sells one. I know many different manufactures are out there but does anyone see it being used for FS parts? I dont know if there is a strength issue since it's not metal but many parts could be make like this. Knob, some panel, or display bezels.

    Any thought's?

  2. #2
    75+ Posting Member
    Join Date
    Jun 2012
    Location
    New Orleans, LA
    Posts
    130
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: 3D Printing

    I'm looking to make some 737 landing light switches using Shapeways.com. I have 3D built up, just need to order a set to see how they look.

    Here's some annunciator boxes I had 3D printed to fit my overhead.

    3D Printed Boxes | Blue Skies - A 737 Cockpit Simulator Project

  3. #3
    Administrator


    W9XE/Project777's Avatar
    Join Date
    Oct 2005
    Location
    Warrensburg, Missouri
    Posts
    254
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: 3D Printing

    Shaun

    Checked out your images. Look pretty darn good. How is the cost compared to other manufactures? Does this look like an economical way of purchasing parts? This might be the type of items I was thinking 3D printing might be good for.

  4. #4
    75+ Posting Member
    Join Date
    Jun 2012
    Location
    New Orleans, LA
    Posts
    130
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: 3D Printing

    I would say your cost for 3D printing (at least ordering a print like I did) is most likely gonna be a lot more expensive than traditional part making methods, such as resin castings, injection molding and CNC'd parts for most items. It's also mostly geared to small items right now, probably less that 8 inches on each axis.

    The little boxes I made cost nearly $3/box to have printed. The same box from OpenCockpits cost about $1.08 (but sadly a little too big for my ProSimPart panels).

    My 737 Light switch model is also looking to be nearly $3.50/each, but that's cheap compared to others who sell them for about $6-7 each for a cast.

    As far as durability, it depends on how thick you make the model. I made my box as thin as it can print, 0.7mm. If you squeezed the box with your fingers it'll bend. Squeeze enough and it'll probably crack. But for sitting in a panel and never to be touched, it'll do fine.

    For items that would be handled/touched a lot you'd want to beef that thickness up alot. It'll probably be pretty strong but it'll also cost a whole lot more. Volume is the determining factor in 3D printing.

  5. #5
    75+ Posting Member
    Join Date
    Jun 2012
    Location
    New Orleans, LA
    Posts
    130
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: 3D Printing

    Here's a DIY 3D printer I came across today. Only $500.

    Solidoodle | Affordable, Easy-to-Use 3D Printers

  6. #6
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,883
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: 3D Printing

    Whether you make sim parts or other.... it just looks like fun to play with

    Matt Olieman

  7. #7
    150+ Forum Groupie


    steveeverson's Avatar
    Join Date
    Nov 2007
    Location
    Lancashire UK
    Posts
    209
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up Re: 3D Printing

    IMG_0232 copy.jpgIMG_0299 copy.jpgIMG_0323 copy.jpgIMG_0326 copy.jpg
    Hi There,
    Built a 3d printer from a kit last year. Quite cheap to build (seeme cnc H1). Ive made a few bits with it mostly using sketch up to design with. Last project was the mechanism for my fire handles.
    Few pics included
    Cheers
    Steve
    another bedroom boeing.....

  8. Likes W9XE/Project777 liked this post