Results 1 to 10 of 10
Thread: Removing the panels in VC mode
-
10-08-2008, 07:08 AM #1
- Join Date
- Sep 2007
- Location
- BRAZIL
- Posts
- 20
Removing the panels in VC mode
Gentlemen ,
How to remove the panels in VC mode ?
Thanks and regards
Alberto
-
10-08-2008, 08:27 AM #2
Good question- I too would like to know how to do this for FSX as well since Im hoping it might improve performance.
-
10-08-2008, 11:01 AM #3
- Join Date
- Feb 2007
- Location
- California, USA
- Posts
- 380
If you would like to remove the entire cockpit interior from the FSX VC, you can use an empty interior airplane model in place of the normal file. I believe there is an empty file used by WidevieW.
It may not be completely empty. It may just have one or two small polygons to keep FSX happy.
-
10-08-2008, 08:58 PM #4
- Join Date
- Sep 2007
- Location
- BRAZIL
- Posts
- 20
Removing the panels inVC mode
Thanks Mike ,
And in FS9?
regards
Alberto
-
10-12-2008, 07:28 PM #5
Hi,
In FS9, I have used a hex editor to remove the VC before with great luck. Always make a backup of the file before you change it (of course)
Here is the complete thread on how to do this..
http://forums.avsim.net/dcboard.php?...ng_type=search
Try the fourth our fifth post down by Douglas K. He explains it quite well!
Hope this helps, Jeff
Here is the specifically relevant text from his post:
**********************
Yes, you can!As far as removing the VC from the A/C model is concerned, it is perfectly possible and actually quite simple to do, involving only a hex editor and two changes to the aircraft.mdl file.
A good hex editor can be found here (Hex Workshop 4.1 - shareware but fully functional for long enough to get the job done and then some):
http://www.bpsoft.com/downloads/
Open the mdl file you want to edit and search for the following hex value: 0022003900
In the first two occurences of that string, simply change the 39 in 0022003900 to 00. It should now look like this: 0022000000. Save the changes, OK the creation of the backup file then exit Hex Workshop to test it out in MSFS.
I have found that this works on mdl files created in GMAX, FSDS, and FSDS2. It works on the default FS9 A/C, including the new vintage models. It takes two minutes at the most to complete, and if a computer moron like me can do it, then anyone can, including chimpanzees.
If you decide to go this route, be sure you use your new mdl file powers for good, not evil.
-
10-13-2008, 08:43 AM #6
Below is an answer from Bill Leaming of Eaglesoft to a post called "Way to remove panel from VC?" at AVSIM.com. Bill is a very knowledgeable gauge programmer.
"Removing the VCockpitXX sections will only get rid of the gauges.
The only way you might get rid of the visual vc model and leave the prop would be to edit all the textures used for the vc panel to be transparent.
With FSX there's no need to 'hex edit' anything, since the VC is simply the seperate xxx_interior.mdl...
...simply edit the model.cfg file and comment out the interior entry to get rid of it entirely!
Bill Leaming
Gauge Programming - 3d Modeling
Eaglesoft Development Group
Intel Core 2 Quad Q6600-4GB DDR2 Corsair PC6400-500 GB SATA-ATI Radeon HD2400 Pro 256MB DX10
NOTE: Unless explicitly stated in the post, everything written by my hand is MY opinion. I do NOT speak for any company, real or imagined..."John
System:
ASUS P5Q SE/R
Intel Q9550 O/C to 3.4 GHz
4 GB 1066 DDR2 RAM
300 GB WD 10,000 RPM Raptor SATA Drive
GeForce 8800 GT 512 KB RAM
Matrox TH2Go with three 19" Sumsung 940 BX
IR Track 4
-
10-13-2008, 08:52 AM #7
The Dreamfleet 727 has the option of loading a VC cockpit with the flight model or not. Great for builders, but the intent was to reduce the frame hit when in VC mode.
Hopefully, we'll see more third-party aircraft using this feature as standard.
The hex editor does work though. I tried it out on other aircraft.Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
07-22-2013, 02:02 PM #8
- Join Date
- Jul 2013
- Location
- France
- Posts
- 2
Re: Removing the panels in VC mode
Hi everyone,
Very nice tweak, it works fine...but I would like to know also if there is a way to remove the flexing wing as we can remove te V-cockpit...if someone can help me....thanks
-
07-22-2013, 02:04 PM #9
- Join Date
- Jul 2013
- Location
- France
- Posts
- 2
Re: Removing the panels in VC mode
sorry I have forgotten...I am on FS9
-
10-29-2016, 03:25 PM #10
- Join Date
- Aug 2014
- Location
- South Africa
- Posts
- 3
Re: Removing the panels in VC mode
This thread is very old but hope someone can help. I want to remove the gauges and panel from VC in FSX but still want to keep VC. I did it before but computer crash and now I don't know how. I tried Bill suggestion but that remove the whole VC.
Similar Threads
-
Removing green text line from main screen
By fvefa in forum MyCockpit Online Flying DiscussionReplies: 0Last Post: 09-06-2010, 03:00 PM -
Removing Monitor Bezel
By Crescent in forum General Builder Questions All Aircraft TypesReplies: 5Last Post: 06-07-2010, 10:48 PM -
Removing the cockpit view from FSX
By JimmyGerrard in forum General Microsoft Flight Simulator 10 (FSX)Replies: 17Last Post: 10-31-2009, 03:00 PM -
Removing camera views
By Martin Cumming in forum General Builder Questions All Aircraft TypesReplies: 0Last Post: 09-08-2007, 01:18 PM
Prettys Womans from your city for night
A320 Sound Files Missing