Results 1 to 5 of 5
  1. #1
    150+ Forum Groupie
    Join Date
    Mar 2007
    Location
    Vancouver
    Posts
    192
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Phidget 64 LED not working

    Hi,

    I've been messing with the 64 LED digital output phidget board. The instructions say that LEDs can be connected to the end of the Molex cable (if uncut). Only trouble is that there's no clear explanation as to which way to connect.

    I plugged in an LED and clicked the test button, but I have had no luck. I tried switching polarity and the same. I'm following the instructions to the letter, except that I'm only using a 300mA power supply instead of the recommended 1.5A. My reasoning is that I'm only driving a single LED and I don't happen to have a spare 1.5A PSU around. The LED I'm using is 20mA so there should be ample power.

    FS2Phidget recognizes the card and indicates status green in the interface. It's just the LEDs I'm using are not working, even in test mode.

    Any thoughts?
    VANCOUVER
    Jet fighter / single pilot sim, plus thinking of a 777 as a secondary sim.

  2. #2
    300+ Forum Addict BlackWidow's Avatar
    Join Date
    Dec 2006
    Location
    Tehacahpi CA, USA
    Posts
    437
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Paul, Try using the recomended power supply. I say this only to rule out that it might be a power supply issue.

  3. #3
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    The other thing that comes to mind, is be sure the leds leads are touching the connector inside the plug. The diameter of the leds leads is thinner then the pins for the board.
    Bob Reed

  4. #4
    150+ Forum Groupie
    Join Date
    Mar 2007
    Location
    Vancouver
    Posts
    192
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Bob Reed View Post
    The other thing that comes to mind, is be sure the leds leads are touching the connector inside the plug. The diameter of the leds leads is thinner then the pins for the board.
    Good point. In fact I actually split the wire and used a crocodile clamp to connect to the LED to ensure connection. I'm not getting anything during the lamp test mode in FS2PHIDGET software.

    I have now contacted the manufacturer as it's probably defective. Thankfully they have a 1 year warranty.

    BTW, I am now using a 12v supply with ample current capabilities, instead of the low power one I tried at first.
    VANCOUVER
    Jet fighter / single pilot sim, plus thinking of a 777 as a secondary sim.

  5. #5
    builder
    Join Date
    Jan 2007
    Location
    Texas
    Posts
    582
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Paul,

    You can test an LED by placing leads directly into Molex connector.
    Sometimes have to wiggle around to make sure you have good connection, but if inserted with correct LED pins in correct Connector holes will illuminate.

    Note that one of the wires in the Molex cable is colored white.
    The LED cathode (negative) HAS to go to that connection.
    Generally, the cathode is the short lead on LED, but don't always bet on it. Is trivial matter to pop LED out of connector and turn around.

    Ensure FS is connected (green status) before pressing Test button on FS2Phidget.

    Regards,
    Alan.

Similar Threads

  1. Replies: 11
    Last Post: 02-28-2011, 04:09 PM
  2. Argh 3 phidget boards nicht working with FS2PHIDGET
    By Paul G in forum FS2Phidget Releases
    Replies: 2
    Last Post: 09-10-2008, 02:50 PM
  3. Phidget 0/16/16 - how to get working
    By Paul G in forum FS2Phidget Users
    Replies: 2
    Last Post: 05-22-2007, 03:20 PM
  4. LED 64 Phidget
    By wchambers in forum Phidgets & Cockpit Simulator Builder
    Replies: 1
    Last Post: 11-09-2004, 09:51 PM
  5. 8/8/8 phidget help
    By imported_737nut in forum Phidgets & Cockpit Simulator Builder
    Replies: 4
    Last Post: 11-03-2004, 06:00 PM