Results 1 to 10 of 15
-
03-15-2010, 08:24 PM #1
- Join Date
- Mar 2010
- Location
- Chicago, USA
- Posts
- 9
Need Help Getting My FSBUS NG I/O Going Again..
Hi All:
I am new to the forum and have started to rebuild my sim again. Around 2006 I bought a FSBUS NG Com and I/O card (only swicthes on it) from a fella in Holland...I think it was Jan but I can't remember.
Well, I tried to hook up my FSClassic Key Card and NG Card (which had been working fin about 2 years ago) and I think I did something the to NG card as I don't get any switch activity. My Classic FSKey works fine on the NG FSCOM.
I have download FSBUS CDK and tried to set the CID to 2 but still I get nothing.
Does anyone have any ideas how I could re-program the chip and how do I do this ? I looked on the FSBUS site and its says use a PonyProg program but I searched the Internat and it doesn't seem to allow me to download this.
I have a ttached a picture of the NG I/O card and you can see it does not have a 2 pin jumper just 6 pin program cable.
Many thanks for anyone's help as I would really like to get this going...JB
-
03-16-2010, 02:58 AM #2
- Join Date
- Jan 2007
- Location
- Netherlands
- Posts
- 201
Re: Need Help Getting My FSBUS NG I/O Going Again..
HI JB,
I think it's fsbus related.
In the setup of the fsbus software is an option to set to Classic or NG.
Try that and see what's happening.
Best regards
Jan Geurtsen
-
03-16-2010, 01:32 PM #3
- Join Date
- Mar 2010
- Location
- Chicago, USA
- Posts
- 9
Re: Need Help Getting My FSBUS NG I/O Going Again..
Thanks Jan:
I am using FSBUs 2.4.1 and have set the Setup to Classic and NG. I went into the Ket test area and set to CID2. As I pressed keys I did not get any change i.e. 1 to 0 etc.
When i connect up my FSKey Classic to same test page all is well and the test keys change.
My NG key card acts like it isn't programmed or something. Any more ideas for me to get her running again ?
many thanks...JB
-
03-16-2010, 02:04 PM #4
- Join Date
- Jan 2007
- Location
- Netherlands
- Posts
- 201
Re: Need Help Getting My FSBUS NG I/O Going Again..
Try to flash the CID again or use ponyprog to re-flash the microcontroller.
See this link to download ponyprog:
http://www.lancos.com/ppwin95.html
Jan
-
03-16-2010, 02:09 PM #5
- Join Date
- Jan 2007
- Location
- Netherlands
- Posts
- 201
Re: Need Help Getting My FSBUS NG I/O Going Again..
BTW the board on the picture is the classic fsbus key card
-
03-16-2010, 03:46 PM #6
- Join Date
- Mar 2010
- Location
- Chicago, USA
- Posts
- 9
Re: Need Help Getting My FSBUS NG I/O Going Again..
Thanks Jan:
Oh dear ...see how much I know ? I thought I had an NG card because it was newer looking than my old classic card !!
To Flash the microcontroller do I flash like I always do with Classic cards i.e. set the 4 pin jumper on the card to the P position (you can see it on the picture) and flash through FSBUS ? What do I need to set on the FSCOM to Flash ?
Would I need to use the PonyProg program if it flashes OK ?
Many thanks...JB
-
03-16-2010, 05:23 PM #7
- Join Date
- Dec 2006
- Location
- Israel
- Posts
- 126
Re: Need Help Getting My FSBUS NG I/O Going Again..
Jan , now i am confused
Are you talking about Ng FSCOM or Classic?
Cant help you with NG as i dont have that, but with the the Classic you flashing PICs on all remaining boards with your old generation fscom and no need for the Pony programmer
Keep your 9 pin cabel connected to the com port of your pc short as possible and set the jumper correct
Some info on the Fscom, and modules ,needed to be flashed jumpers settings , you can still find here
http://www.mikkila.org/fsbus/doc/layout_e.php
Hopefully thats helps
Regard
Joseph
-
03-16-2010, 05:23 PM #8
- Join Date
- Jan 2007
- Location
- Netherlands
- Posts
- 201
Re: Need Help Getting My FSBUS NG I/O Going Again..
Hi JB
No, you need a 6 pin cable to flash the microcontroller on the NG board together with Ponyprog and the FSCOM board
You will find a discription in the documentation of the IO board, see the manual on the fsbus webpage .
Finaly you can set the CID with the 10 pin cable.
-
03-16-2010, 05:27 PM #9
- Join Date
- Jan 2007
- Location
- Netherlands
- Posts
- 201
-
03-18-2010, 01:15 PM #10
- Join Date
- Mar 2010
- Location
- Chicago, USA
- Posts
- 9
Re: Need Help Getting My FSBUS NG I/O Going Again..
Thanks to everyone for your help...I will try tonight to see if I can get the board running again...many thanks...JB
Similar Threads
-
Fsbus CDK
By flyandre in forum General Builder Questions All Aircraft TypesReplies: 4Last Post: 12-27-2014, 12:58 PM -
Fsbus ng io
By Davral in forum I/O Interfacing Hardware and SoftwareReplies: 0Last Post: 01-10-2009, 10:38 PM -
Fsbus 2.4.3
By Anderson/SBSP in forum I/O Interfacing Hardware and SoftwareReplies: 9Last Post: 11-30-2008, 04:25 PM -
Fsbus
By 388TH_A in forum I/O Interfacing Hardware and SoftwareReplies: 3Last Post: 11-16-2008, 05:15 PM -
Help FSBUS
By cesarfsim in forum I/O Interfacing Hardware and SoftwareReplies: 2Last Post: 10-26-2008, 02:23 PM
Sexy Womans in your town for night
Run-Time Check # 0 - The value of...