Results 1 to 7 of 7
  1. #1
    500+ This must be a daytime job 737NUT's Avatar
    Join Date
    Feb 2006
    Location
    Indianapolis, IN
    Posts
    760
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Real VSI+$40+1hour=Working real gauge!

    Hi all,
    Well i wish it was all this easy but reality knows it isn't. Now this particular gauge was.

    I bought for 24.95 off of ebay,looks unused and brand new!

    Any way, if you look close, it is driven by a small dc motor and has a potentiometer for position feedback. Sound familiar??? SERVO!!!!!!!!!!!!!!!! Soooo, i took an old traxxes servo from an old rc car, desoldered the motor, cut off the pot. I then solder leads from the gauge motor to the servo pcb were the original motor was. Then i used a simple servo lead soldered to the pot in the gauge and simply plugged it into the legs of the pot that was cut off of the servo pcb. Then plugged the "new" servo into the OC servo board and a quick SIOC program. PRESTO!!! A perfectly working smooth as melted butter operating real 737 or 727 VSI gauge. This was way to easy! But cool none the less. See attached pics, any questions feel free to ask.





    Attached Images Attached Images
    Last edited by Matt Olieman; 12-31-2009 at 12:50 PM. Reason: Made Pics Visible :)

  2. #2
    150+ Forum Groupie twisted8's Avatar
    Join Date
    Jun 2009
    Location
    California
    Posts
    220
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    good job!, no need to spend hundreds or know much about electronics when you can use OC cards, well done!

  3. #3
    300+ Forum Addict BlackWidow's Avatar
    Join Date
    Dec 2006
    Location
    Tehacahpi CA, USA
    Posts
    437
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    Cool that looks awesome.
    Mike G.

  4. #4
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,883
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    Nice job Rob!!!!! and the cost is fantastic

  5. #5
    500+ This must be a daytime job 737NUT's Avatar
    Join Date
    Feb 2006
    Location
    Indianapolis, IN
    Posts
    760
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    Just to update, i have over 40hrs on this set-up now and it is still working flawless! Much better than the simkits set-up i had before. It always needed recalibrated. Next up is a servo altimeter.

  6. #6
    Executive Assistant Geremy Britton's Avatar
    Join Date
    Jul 2007
    Location
    North,East England
    Posts
    1,445
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    That's amazing! ... will you interface mine if i send you it?
    Even better, if you could create a more detailed tutorial for the tutorials area about exactly what you did.

    Thanks for the post,
    Geremy Britton
    Executive Assistant, MyCockpit Inc
    Head of GLB Flight Products
    www.geremy.co.uk

  7. #7
    500+ This must be a daytime job 737NUT's Avatar
    Join Date
    Feb 2006
    Location
    Indianapolis, IN
    Posts
    760
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Real VSI+$40+1hour=Working real gauge!

    Quote Originally Posted by Geremy Britton View Post
    That's amazing! ... will you interface mine if i send you it?
    Even better, if you could create a more detailed tutorial for the tutorials area about exactly what you did.

    Thanks for the post,
    Sure, i can modify yours as long as it is a servo'd VSI. Thats the key to making it easy.

Similar Threads

  1. Latest picture and update on my real 727 engine gauges working
    By 737NUT in forum Interfacing Real Aviation Parts
    Replies: 11
    Last Post: 07-31-2011, 11:45 AM
  2. Real bulbs for real parts
    By LH784 in forum General Builder Questions All Aircraft Types
    Replies: 3
    Last Post: 01-27-2009, 08:25 PM
  3. Real 1.5" yaw damper gauge
    By Jackpilot in forum General Builder Questions All Aircraft Types
    Replies: 8
    Last Post: 10-14-2008, 07:45 PM
  4. working a real gauge without PMSys.
    By Jackpilot in forum General Builder Questions All Aircraft Types
    Replies: 44
    Last Post: 10-03-2008, 09:22 PM