Results 1 to 6 of 6
  1. #1
    F-111 over Brisbane
    Join Date
    Dec 2009
    Location
    Australia
    Posts
    28
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    F111 Dual control

    Hi folks,

    I have been constructing a F111 crew module and the dual control I have started to make isnt working real well at all.
    I have given up on the rudder pedals at the moment and have focused on the yoke controls.
    at this point in time I have two USB contollers,with one as the master. The master is connected to the computerand internal wiring connects the two connectors together.
    Mechanically the two yokes are connected by a cross bar, but the full range of movement is very sloppy and large error is evident on the slave side especially in the forward/aft movement.

    Can anyone help in a better design.

    Kind regards

    SIRA66
    IMG_0515..jpg

  2. #2
    F-111 over Brisbane
    Join Date
    Dec 2009
    Location
    Australia
    Posts
    28
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: F111 Dual control

    After much toil I have found a solution that suits me and i dare say I will modify it as time goes on.
    The problem I found with my old Dual stick control was that forward and aft movement across the two controls created an error at the other side. The sideways movement worked fine and no error was observed.
    IMG_0515..jpg
    If you look close at the Control stick the two are connected by a sway bar connected at the bottom of the contol shaft.
    My solution was to provide a non-pivoting lateral beam in the yaw axis but allow the pitch axis to rotate.
    I had to allow the structure to allign with the control sticks and the pivoting base so the two did not interfere with each others moment.
    The lateral beam slid over the existing beam as a tube to allow roll axis to move. You'll see what I mean.
    And the darndest thing it actually works!!
    They say that the mother of all invention is necessity......I think they're right!!!
    Attached Images Attached Images

  3. #3
    F-111 over Brisbane
    Join Date
    Dec 2009
    Location
    Australia
    Posts
    28
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: F111 Dual control

    IMG_0657.jpg

    As you can see the paint has gone on and the decals aas well. It looks 1 Million dollars to what it did. Unfortunately the display computer crashed half way through the open cockpit day. More work to do....but thats life!!

  4. #4
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: F111 Dual control

    Hi there,

    Push pull cables can be very effective such as the type on vehicle or outboard motor throttle controls. Even a simpler idea - I have utilized small pulleys and trace wire to link my rudder pot to the tiller handle on my 737, it works very accurately and trace wire is very strong.

    This is how my rudders are linked -



    Cheers, Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  5. Thanks sira66 thanked for this post
  6. #5
    F-111 over Brisbane
    Join Date
    Dec 2009
    Location
    Australia
    Posts
    28
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: F111 Dual control

    Thanks Westozy for the pictures about your rudder controls,
    I will see if I can scale it down into there module.

    Thanks mate.

    SIRA66

  7. #6

    Re: F111 Dual control

    Development of high-speed F-111 aircraft needed for a better exhaust system caused. Ejectable crew module was designed to meet this need. ADF force structure in the F-111 has demonstrated the role of conventional strategic deterrent, ADF with total forgiveness to attack strategic targets allowed.

Similar Threads

  1. Dual radios with dual headsets
    By frazer in forum Cockpit Sounds
    Replies: 2
    Last Post: 01-13-2011, 04:40 AM
  2. Dual SIOC
    By Oter3 in forum OpenCockpits General Discussion
    Replies: 6
    Last Post: 05-25-2009, 05:17 PM
  3. dual interface
    By djcevera20 in forum General Builder Questions All Aircraft Types
    Replies: 3
    Last Post: 04-15-2009, 12:22 AM
  4. dual head or dual card
    By Jackpilot in forum Computer Hardware Setup
    Replies: 1
    Last Post: 02-18-2009, 03:26 PM
  5. dual FMC
    By John Ebbers in forum PM General Q & A
    Replies: 0
    Last Post: 03-01-2006, 09:07 PM