Page 1 of 2 12 LastLast
Results 1 to 10 of 16
  1. #1
    150+ Forum Groupie
    Join Date
    Mar 2007
    Location
    Vancouver
    Posts
    192
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question about resistor heat

    Hello - hoping this is the best place to ask this question.

    I'm creating some flood lighting using a 1/2 U channel aluminum with a few high brightness LEDs. Found a calculator and circuit to connect in series with a 12 Volt supply.

    My question is not about voltages, resistor values or anything like that. However the resistor is too hot to touch when operating, although prongs, and leds and wires are cool. Just worried that it's a fire hazard.

    Tech details:

    12 volt supply. LEDs 2.4v @ 30mA, resistor is 150 ohm and connected in SERIES with 3 LEDs. Resistor is rated at 0.25 W so should be well under the 70mA that the calculator suggests.

    Question: Is this ok for the resistor. As it's not going to be near anything flammable then I don't see it as much of a risk, but as my project is not the most fire retardant structure, I'd rather crash and burn in a real plane than a home built sim.

    Thanks

    Paul
    VANCOUVER
    Jet fighter / single pilot sim, plus thinking of a 777 as a secondary sim.

  2. #2
    10+ Posting Member
    Join Date
    May 2007
    Location
    Near Winnipeg, MB, Canada
    Posts
    17
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hello Paul:

    Greetings from a fellow Canuck.

    There is an on-line calculator at http://www.electronics2000.co.uk/calc/calcpow.php which you will find helpful in solving this problem.

    Go to the bottom of the page and you can enter values. Use the drop down menus to obtain milliamps.

    When I enter 60 ma and 150 ohms, it comes up with 540 milliwatts of power dissipated in the resistor ... that is twice its rated 1/4 watt value and would account for the heat you are experiencing.

    You should step up to at least a 1/2 watt resistor, but I always like to be conservative by at least a factor of 2 unless space is a great consideration. Therefore a 1 watt 150 ohm resistor will serve you well and should run cool to the touch.

    Regards,
    Lee Smith

  3. #3
    150+ Forum Groupie
    Join Date
    Mar 2007
    Location
    Vancouver
    Posts
    192
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi,

    Thanks for the calculations. I'm trying to work out where you got 60 mA from. My calculator is based on 30. When I work out the power it comes to 70mW so a quarter watt should be enough, right?

    As an aside, if I add another identical resistor in parallel to the first, will that help dissipate some of the heat? I did try this and they both get hot. I'm not trying to be a tight *** as these things are a few cents each, but I have to buy 100 of them for each value, and the store is 20 minutes drive. If I can find a one-off work around that would be better. Although I'm now starting to wonder whether I just put a resistor on each one and wire it accordingly.

    Thanks again for your referral.

    Paul
    VANCOUVER
    Jet fighter / single pilot sim, plus thinking of a 777 as a secondary sim.

  4. #4
    1000+ Poster - Fantastic Contributor AndyT's Avatar
    Join Date
    Jun 2006
    Location
    Oahu, Hawaii
    Posts
    1,228
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Simple rule:
    If the resistor is so hot you can get burned, then its too small for the job.
    God's in command, I'm just the Pilot.
    http://www.geocities.com/andytulenko/

  5. #5
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    What Andy said.

    Change to a higher wattage, they'll be fine. If they're too hot, they're too small.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #6
    25+ Posting Member
    Join Date
    Apr 2008
    Location
    Frankford, Ontario
    Posts
    59
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Paul,

    If your LEDs each drop 2.4V when passing a current of 30mA, and they are in series, then you must pass 30mA through the series resistor too.

    Your supply is 12V, the LEDs drop a total of 3 x 2.4V= 7.2V, so your resistor needs to drop 4.8V with 30mA going through it.

    So the value of the resistor should be R=V/I or 4.8/30mA, which is 160 Ohms.

    And the power rating of that resistor, given by W=VxA is 4.8x30mA, or 144mW.

    So with a resistor of 160 Ohms, a quarter watt rating is OK, but better with a half watt for longer life.

    With a 150 Ohm resistor, the current through the circuit will be slightly higher by a couple of mA, which won't affect things significantly, so the wattage of your 150 Ohm resistor certainly ought to be enough.

    If it's too hot to touch, then the assumption that your LEDs are each dropping 2.4V is wrong. Or the resistor isn't 150 Ohms! Can you measure it?

    Can you measure current and voltage? If so, measure the current through the circuit, and then measure the voltage across each of the components. The current should be about 32mA and the voltages should be as above.

  7. #7
    10+ Posting Member
    Join Date
    May 2007
    Location
    Near Winnipeg, MB, Canada
    Posts
    17
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Since there are 3 LEDs .. each consuming 30 Ma at manufacturers max power ratings, the cumulative current would be 90 Ma plus the amount of energy dissipated in the resistor.

    I had a dislexic moment and went with 2 x 30 Ma in my first post rather than current for 3 LEDs. Hence, my original use of 60 Ma in the calculator results.

    Going to the calculator again, it indicates 1.215 watts.

    Bottom line ... as mentioned earlier, if the resistor is running so hot that you can't touch it, it is waaaay too under rated. It should remain very close to room temperature, or just barely warm to the touch.

    Generally, electronic components are rated at 25 degrees C. surface temp although internal component temps will be higher.

    Lee

  8. #8
    25+ Posting Member
    Join Date
    Feb 2008
    Location
    canton ga.
    Posts
    55
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Lee
    I think you were right the first time current is the same through all components in a series ckt. What is missing is the true resistance of the leds + resistor ohms to figure a true current then you can figure Watts. But I am not sure how you put LEDS in a series CKT, I would think it would be a parallel CKT. A resistor would be in series with each LED but LEDS would be in Parallel. (I think)

    percy.

  9. #9
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    LED's in series with one resistor in series with all, keeps all led's at the same brightness. If you do not have the resistor, the first led will be the brightest and the last led will be the dimmest.

    Trev
    ________________________
    Trevor Hale

  10. #10
    150+ Forum Groupie
    Join Date
    Mar 2007
    Location
    Vancouver
    Posts
    192
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I think I'm going to change my design to a set of parallel, single LED - single resistor circuits as I've done with other parts of my sim. These LEDs run really cool and parallel means you don't have to account for how many LEDs you have.

    Still confused over what was said about current. I'm pretty sure it's consistent as analogous to water flow, but voltage IS dropped per component. I'll treat advice here with more respect than the theory. Something sure is amiss but I'm not going to entertain fire risks to find out why

    Thanks for all the help

    Paul
    VANCOUVER
    Jet fighter / single pilot sim, plus thinking of a 777 as a secondary sim.

Page 1 of 2 12 LastLast

Similar Threads

  1. FSBUS i/o card - resistor connect in series
    By adacho in forum I/O Interfacing and Hardware
    Replies: 2
    Last Post: 08-19-2010, 05:35 AM
  2. LED resistor placement
    By mterm in forum I/O Interfacing and Hardware
    Replies: 2
    Last Post: 04-09-2009, 08:34 PM
  3. Carb Heat Switch
    By GARich in forum General Aviation (GA) Builder Disccusion
    Replies: 8
    Last Post: 01-21-2009, 03:27 PM
  4. heat problem
    By Radar in forum Computer Hardware Setup
    Replies: 8
    Last Post: 03-11-2008, 10:07 PM
  5. Powering LED's : use a resistor or not?
    By shawnpwilson in forum Phidgets & Cockpit Simulator Builder
    Replies: 1
    Last Post: 01-18-2005, 06:21 AM