Results 1 to 8 of 8
Thread: Real Korrys Real Trouble...
-
11-09-2008, 03:56 AM #1
Real Korrys Real Trouble...
Hi guys,
I was lucky enough to get my hands over 30 real world airbus Korrys, which im expecting to arrive in a few days.
Does anyone here has any experience adapting real world Korrys to the flightsim?... If so, can you share a bit of your experiences, because im a bit scared with the possibility of not knowing what on earth should i do with them when they arrive...
Thanks!
Alex
-
11-09-2008, 08:49 AM #2
Terminals #1 & #3 IIRC will light the indicators when voltage is applied. They are 28VDC, but 24VDC will light them up brightly and increase the bulb life.
There is a diode present in the circuit so they are polarity sensitive. This allows a press-to-test function and/or an all-on type test from another circuit.
There is also a schematic diagram of the indicator right on the case of the indicator. There are a lot of ways you can wire these, but I didn't get elaborate with mine.
To disassemble the indicator for mounting, gently pull out the light cap and unscrew the two brass allen-head screws deep in the socket. DO NOT REMOVE THEM. Now you can remove the back half from the front half and the mounting bezel.
Note which way is up for all pieces. They must be reassembled correctly.
These are very expensive indicators and are like gold in the sim community. Be gentle with them and be careful you don't damage them while working with them.
IIRC, the bulb is a 387.Last edited by Michael Carter; 11-09-2008 at 08:52 AM.
Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Dislikes
-
11-09-2008, 03:19 PM #3
Hi Michael,
I have to say im trully amazed with the kindness i see around here..everyone seems to really care for others problems, something that aint all that easy to find..so, and in advance, i thank you for all the support given.
Now...Korrys... your answer was great..you avoid me some troubles. I know they are very valuable pieces, and they do give some "real world soul" to the project...so ill be really carefull, and if you agree, ill post some pics in case i have questions regarding proper connection.. Your help will be really valuable
Thanks again my friend
Alex
-
11-09-2008, 03:20 PM #4
-
11-09-2008, 03:36 PM #5
Actually if they are Airbus KOrry's those lamps operate on 5V I think if they are Led's theya re easy to wire!
Roberto
-
11-09-2008, 04:12 PM #6
Hi Roberto,
What if they are pre-1998?... Im asking this because i have a real External Light & APU panel, that is from 1997, and it operates with 34, 5v bulbs...no leds there.. As far as i know LEds are all post 1998.. can you confirm me that?..
Thanks for the reply roberto.
Cheers mate
Alex
-
11-09-2008, 09:17 PM #7
The Chroma Lux 318 Korry with LED's already contains the circuitry to drop the voltage to the required LED voltage. You will still use 24-28VDC to power them.
Actually, all of the Korry LED equipped indicators regardless of series have the required internal circuitry.
For a real aircraft or a simulator using aircraft voltage they're pretty much plug-n-play. No changes are required to the voltage buss for these indicators.
Light plates for panels are 5VDC. Some Gables heads do use 28VDC though. I don't know why they're the oddball in some cases. It might be so that they can run directly off the hot battery buss if the AC and TR's fail.
Visit Korry here http://www.korry.com/products/switch...omalux_318.stm so you can familiarize yourself with your new indicators. Each indicator has a .pdf document that explains wiring options and physical dimensions with cutout sizes.Last edited by Michael Carter; 11-10-2008 at 07:51 AM.
Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
NNomad007 thanked for this post
-
11-10-2008, 05:06 AM #8
Thanks for the help mate, ill take a close look at those specs and ill keep you all updated when the korrys arrive.
Cheers!
Alex
Similar Threads
-
Real VSI+$40+1hour=Working real gauge!
By 737NUT in forum Interfacing Real Aviation PartsReplies: 6Last Post: 01-11-2010, 01:35 PM -
Real bulbs for real parts
By LH784 in forum General Builder Questions All Aircraft TypesReplies: 3Last Post: 01-27-2009, 08:25 PM -
Real 737-800 CDU
By Daniel Schiffer in forum PM General Q & AReplies: 0Last Post: 03-17-2006, 08:19 AM
Prettys Womans from your city for night
A320 Sound Files Missing