Results 1 to 10 of 15
Thread: WWII Yokes
-
08-29-2008, 07:43 PM #1
WWII Yokes
Does anyone know of a company that currently builds or could build different yokes from ww2 aircraft? Thanks.
-
08-29-2008, 11:18 PM #2
From what I've seen at APHS, most American bombers used what looks pretty much like an auto sterring wheel with the top third cut out.
It shouldn't be too much of a stretch to build one of these yourself.
Have a look here: http://www.angelfire.com/il2/aphs/wheels/wheels.html
There are a lot of modern yokes mixed in with the old ones, so look carefully through all of the photos. There is a B-24, B-25, P-38, and others to see.Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
08-30-2008, 01:09 AM #3
Hehe. Building one wouldn't be a problem, but I would have no clue as to how to make it accurately work with a game.
-
08-30-2008, 02:02 AM #4
Hi Crescent,
Here's a simple joystick interface solution I am making for a Spitfire builder...
Regards,
Gwyn
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikesmagicaldr thanked for this post
-
08-30-2008, 06:54 AM #5
Gwynn,
For the Roll pot, why not just fatten up the pot shaft and stick it in the end of the tube? A lot less hassle that way.God's in command, I'm just the Pilot.
http://www.geocities.com/andytulenko/
-
08-30-2008, 08:48 PM #6
Hi Andy,
That would only put about 20 degrees of rotation on the pot, this would be less than 10% of a common rotary pot's available travel. For best results, pots should have all of their available travel used, it's much better for accuracy and calibration. It's also a normal industry standard to maximize pot travel. Your idea would work and obviously and be simpler to build. Using a hacked USB joystick would be a good option because they only have small amounts of pot travel.
Gwyn
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
-
09-02-2008, 08:34 PM #7
-
09-03-2008, 11:03 AM #8
Thanks for the replies. Is there a good guide on the site describing how to wire etc. a yoke/throttle? I don't have the foggiest idea how this is done hehe, but it seems to be the thing to do if you want it as real as it gets. Thanks.
-
09-03-2008, 11:19 AM #9
You can cannibalize any two axis joystick or yoke and just use those innards.
It'll be prewired already; you'll just have to rig up the linkage for each axis.Boeing Skunk Works
Remember...140, 250, and REALLY FAST!
We don't need no stinkin' ETOPS!
Powered by FS9 & BOEING
-
09-03-2008, 03:23 PM #10
I just rewired my CH USB yoke and rudder pedals to use one of those 12 bit high resolution USB interfaces from England, I am sorry, forgot the name of the product off the top of my head, it is TOP quality. The hardest part was figuring out the button matrix wiring of the CH yoke without putting in all new wires. I figured it out. I even ripped the guts out of my Pro pedals and hooked them into the same card as the CH electronics were acting up on me.
As far as wiring, just look at examples on the net and play with it. Some basic electronics is in order so you know what a common or ground is, how to solder, what a diode is for, etc.
Nice thing about electronics is that its a small investment to get into, unlike machining.
Similar Threads
-
737 yokes, where to buy
By Goldmember in forum Cockpit Parts and Motion PlatformsReplies: 6Last Post: 12-14-2010, 04:59 AM -
Double set with CH yokes&pedals causes yokes to spike
By MortenHa in forum General Builder Questions All Aircraft TypesReplies: 3Last Post: 01-29-2010, 12:44 PM -
WWII sims, Anyone?
By btlnco in forum General Builder Questions All Aircraft TypesReplies: 20Last Post: 12-20-2009, 07:33 AM -
Need Help with my yokes
By QF6228 in forum General Builder Questions All Aircraft TypesReplies: 29Last Post: 05-19-2007, 09:42 AM -
yokes
By Radar in forum Where to Start Building a Home CockpitReplies: 1Last Post: 04-20-2007, 11:29 PM
Girls in your town
A320 Sound Files Missing