Results 1 to 6 of 6
  1. #1
    500+ This must be a daytime job



    Join Date
    Oct 2009
    Location
    Juneau, AK
    Posts
    547
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Spring help please!~

    I need an answer for dummies about how to choose an extension spring.

    I am trying to spring load my parking brake so that the handle requires force to pull out, and pulls back into it's detent when the force is released. Distances are appx 45mm length when relaxed, and appx 120mm when loaded. Force required is just a matter of feel, but I am thinking a kg or so when fully loaded. I am very flexible on this.

    Problem is that every coil spring I have tried from the hardware store when stretched that far loses it's set, and will no longer recoil to it's relaxed position.

    What should I be looking at to solve this problem? Am I stretching the spring too far by asking for a 3x extension, or should I be looking for a different coil diameter spring? A different material?

    Any input would be greatly appreciated!

    Reid
    http://juneaucessnasim.blogspot.com
    N58243 (virtual)- Low and Slow...

  2. #2
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Spring help please!~

    Hi Reid,
    I too have the same issues at times with spring selection and in the end it usually comes down to the good old trial and error method! When I was building my Boeing rudder sets recently I tried three different springs on the brake action until I achieved the desired feel. I wouldn't stretch an extension spring more than twice it's length as a rule. You might try asking your question directly to a spring manufacturer, they are usually quite helpful.
    Cheers, Gwyn (Westozy)

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  3. Thanks AK Mongo thanked for this post
  4. #3
    500+ This must be a daytime job Ronson2k9's Avatar
    Join Date
    Apr 2009
    Location
    London, ON Canada
    Posts
    506
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Spring help please!~

    This is going to sound silly but if you think of what the parking brake does.
    - It rotates the cam to push the brake shoes open. This cam is spring loaded.

    With that in mind you may want to look at a cars (automobile) brake assembly for your answer. You may want to try an auto parts store for a brake shoe spring then add a cantilever to the spring. This will simulate a brake assembly and let you adjust the force by changing the fulcrum on the cantilever. The cantilever (bell crank) will be your cam. The greater the distance from the fulcrum on the PULL side will give you less resistance.

    How are you doin' haven't heard from you for a long time. I've been sick as a dog as of late (pretty bad cold). It broke today though so things should be back to normal for me in a few more days. Yesterday though sore throat, sinus congestion, the whole nine yards. I was burning the candle at both ends for a time and it caught up to me.
    Up Up and away in my beautiful my beautiful - Amphibian

  5. Thanks AK Mongo thanked for this post
  6. #4
    10+ Posting Member maussuam's Avatar
    Join Date
    Feb 2010
    Location
    Berlin
    Posts
    23
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Spring help please!~

    Hi Reid,

    perhaps you could use a couple of elastic staps. The ones used for model airplanes to fix the wings on the fuselage are quite strong.

    Cheers, Bastian

  7. Thanks AK Mongo thanked for this post
  8. #5
    500+ This must be a daytime job



    Join Date
    Oct 2009
    Location
    Juneau, AK
    Posts
    547
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Spring help please!~

    Thanks for the ideas gents.

    Things are going fine, Ron. I have had a bit of a lull in my building, but am working on putting some of the dusty pieces together again. Had a great trip a few weeks ago to Washington DC and the National Air and Space Museum and Udvar-Hazy Center. Got to see a lot of neat aircraft there! Inspired me a little to get my butt in gear and build.

    They had a 152 at Udvar Hazy that was on static display, that you could sit in and try the controls. Gave the impression that I was right on track with my controls. The docent thought I was a little strange when I asked to get in, and was mainly interested in the the feel of the stabilizer trim. He was telling me about pitch and roll, and I was interested in only turning the trim wheel. LOL.
    He looked even more puzzled when I told him why I was doing it, and looked relieved when I finished and moved on!

    I think I will just adjust my spring length to one that is about 100mm long, then I should have the ability for tight recoil, with less than 100% extension. Will have to change my spring mount, but that won't be the first design change in this project!
    Last edited by AK Mongo; 04-13-2011 at 01:45 PM. Reason: additional comments needed
    http://juneaucessnasim.blogspot.com
    N58243 (virtual)- Low and Slow...

  9. #6
    500+ This must be a daytime job



    Join Date
    Oct 2009
    Location
    Juneau, AK
    Posts
    547
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Spring help please!~

    That did it! Lengthening the resting length relative to the extended length solved the problem. Thanks for letting me use this forum as a sounding board.

    Reid
    http://juneaucessnasim.blogspot.com
    N58243 (virtual)- Low and Slow...

Similar Threads

  1. Spring loading for Flaps lever
    By Jackpilot in forum General Builder Questions All Aircraft Types
    Replies: 3
    Last Post: 08-13-2009, 10:17 AM
  2. Gas Spring dampeners for Rudder Pedals
    By Polmer in forum Where to Start Building a Home Cockpit
    Replies: 3
    Last Post: 05-26-2007, 09:30 PM
  3. Spring sizes
    By NicD in forum Cockpit Parts and Motion Platforms
    Replies: 4
    Last Post: 04-03-2007, 03:31 AM

Tags for this Thread