Results 1 to 5 of 5
  1. #1
    1000+ Poster - Fantastic Contributor Tomlin's Avatar
    Join Date
    Nov 2005
    Location
    Waycross, GA
    Posts
    1,025
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Avionics Master Switch vs. Avionics Switch???

    Im having a time trying to understand the difference between Master Battery, Avionics, and Master Avionics Switch.

    My train of thought is that when the Battery Switch is ON, it supplies power to the aircraft's systems and when the Avionics Master Switch is ON, it enables the avionics to be turned on and also causes the Display Units to turn ON. However, the LJ45 handbook references having the L & R Avionics Master Switch Turned OFF for Battery starts, but if the Display Units are not showing data, then you are a bit in the dark as to the Engine Stats (oil pressure, fuel flow, etc) and these need to be monitored while starting.

    Here's where Im thinking the difference lies between offset 2E80 (Master Avionics Switch) and 3103 (Avionics). One offset causes the DUs to come online and the other actually causes the NAVs and COMs be available? Perhaps when turing on the Master Batt it brings the DUs online, but the actual data is not shown till the Master Avionics switch is pressed.

    Can someone shed some light here?

    Thanks,
    Eric Tomlin-
    Learjet 45 Builder
    www.flightlevel180.org

  2. #2
    300+ Forum Addict
    Join Date
    Jan 2007
    Posts
    496
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Tomlin View Post
    Here's where Im thinking the difference lies between offset 2E80 (Master Avionics Switch) and 3103 (Avionics).
    They are both the same. 3103 was my mapped value whilst 2E80 was an unofficial "discovered" value, back in the days when such discoveries could be made by searching with FSInterrogate (FS2000) -- i.e. when there still was a "GLOBALS.DLL which partially resembled the one we has in FS98 and before.

    Same applies to 281C and 3102 for the master battery switch.

    For a long time most of the 2xxx and some 3xxx range of offsets remained unsupported (in a separate table in the FSUIPC lists) because I expected them to change, whilst the 310x set, amongst others, was destined to be re-mapped internally to always provide the correct function.

    In the event, all of the "real "GLOBALS" disappeared in FS as data was absorbed into different FS modules and C++ private class data, and I relented and decided to support, by similar mapping, the more commonly used but previously non-guaranteed offsets.

    Regards

    Pete

  3. Thanks Tomlin thanked for this post
  4. #3
    1000+ Poster - Fantastic Contributor Tomlin's Avatar
    Join Date
    Nov 2005
    Location
    Waycross, GA
    Posts
    1,025
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks, that was one part of the problem/issue, 'What's the difference in FSUIPC' aspect.

    Now here's some additional info to throw into the mix.

    In the PMRJ software, upon turning the BATT ON, you typically wont see anything happen save maybe your taxi/external lights come on but of course when Avionics are ON, then you get the Display Units and of course, your avionics such as NAV, COM, autopilot stuff, etc.

    However, if you turn OFF the BATT switch, the Display Units remain ON, yet you lose your Avionics (Nav/Com) tuning/recieving capabilities.

    What Im trying to determine is this:

    When entering the aircraft (specifially the LJ45), and you turn ON the BATT switch, do the DUs come alive and then the actual function of Avionics come available once AVIONICS are turned ON, or do the DUs not show up at all until the Avionics Switch is pressed ON?


    YES- I have the actual Training Manual for the LJ45, but this is one issue I cannot determine how the real plane behaves, and assume it is similar to any other Glass Transport Aircraft.
    Eric Tomlin-
    Learjet 45 Builder
    www.flightlevel180.org

  5. #4
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Eric, I'd find a Lear pilot and pick his brain.

    Try some of the pilot forums out there and see if you can't turn up something.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #5
    1000+ Poster - Fantastic Contributor Tomlin's Avatar
    Join Date
    Nov 2005
    Location
    Waycross, GA
    Posts
    1,025
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Boeing Skunk Works View Post
    Eric, I'd find a Lear pilot and pick his brain.

    Try some of the pilot forums out there and see if you can't turn up something.
    You'd think with as much documentation that I have on this bird that I would know! Actually, thinking back on when I visited N430FX, I do seem to recall that when pressing the L & R Avionics switch, the displays came alive with all the data, but when the L & R BATT was pressed on (before the AV) the displays only shows a partial Avionics display, but fully the EICAS- you just jogged my memory! I think where the issue lies is in how PMRJ works and Ive used it for so long that it caused me to forget how the real bird works. Guess I need to learn some programming now.
    Eric Tomlin-
    Learjet 45 Builder
    www.flightlevel180.org

Similar Threads

  1. Master caution switch pmdg
    By BishBash in forum Where to Start Building a Home Cockpit
    Replies: 7
    Last Post: 02-13-2010, 10:25 AM
  2. Airbus A320 Engine Master Switch Dimensions
    By Goose in forum General Builder Questions All Aircraft Types
    Replies: 18
    Last Post: 04-23-2009, 03:29 PM
  3. Sim-avionics
    By jongas in forum Computer Hardware Setup
    Replies: 1
    Last Post: 02-27-2009, 07:10 PM
  4. Airbus Master Switch
    By NNomad007 in forum My Cockpit Update
    Replies: 15
    Last Post: 10-29-2008, 02:07 PM
  5. Master BATT and Master Avionics confusion
    By Tomlin in forum PM RJ GC
    Replies: 4
    Last Post: 08-25-2008, 09:03 AM