Results 1 to 7 of 7
Thread: I have a wiring question.
-
08-08-2007, 08:24 PM #1
I have a wiring question.
I made a bit of a goof, when I purchased some great looking LEDs for my gear indicators. The look a lot like the real ones. The problem is that after I bought them, I realized they are 12vdc LEDs.
My question is in activating them. I had planed on using the OpenCockpits IO card to send the 5 vdc to the LEDs by the use of SIOC code. Do I need to use a relay that will be activated by the 5 vdc signal to get 12vdc to the LEDs? If so, how do I turn them off when the gear are up in the wells?John
System:
ASUS P5Q SE/R
Intel Q9550 O/C to 3.4 GHz
4 GB 1066 DDR2 RAM
300 GB WD 10,000 RPM Raptor SATA Drive
GeForce 8800 GT 512 KB RAM
Matrox TH2Go with three 19" Sumsung 940 BX
IR Track 4
-
08-08-2007, 09:10 PM #2
- Join Date
- Feb 2007
- Location
- California, USA
- Posts
- 377
John,
I'd try them on 5 volts and see how bright (or dim) they are. My guess is that what you have is a led packaged with a series resistor. Running it on 5 rather than 12 volts should result in roughly a third the full rated current and less light output.
That may actually be better if you run your sim in a darkened room. At 12 volts they may be designed to be clearly visible in full daylight, and far too bright in a dim room.
-
08-08-2007, 10:18 PM #3
Hi Mike, Good to see you here. These are a bunch of builders. How's the new book coming? Be sure and print enough copies so I can get one.
I will try the 5 volts. It may be a while, however. I still have to figure a way of mounting the three outside view 19" monitors without destroying them. Then I start hooking up the electronics stuff.
Meanwhile, I have to go to Canada and Wyoming on business. Damn oilfield keeping me busy. It is as bad as the early 1980's. Just hope we don't go boom again. LOLJohn
System:
ASUS P5Q SE/R
Intel Q9550 O/C to 3.4 GHz
4 GB 1066 DDR2 RAM
300 GB WD 10,000 RPM Raptor SATA Drive
GeForce 8800 GT 512 KB RAM
Matrox TH2Go with three 19" Sumsung 940 BX
IR Track 4
-
08-08-2007, 10:32 PM #4
Hi Mike, I too always look forward toward your input and, make sure there's a copy of the new book for me too.
-
08-08-2007, 11:11 PM #5
- Join Date
- Feb 2007
- Location
- California, USA
- Posts
- 377
The book (http://www.mikesflightdeck.com/upcoming_book.htm) is about 75% drafted. I've got 457 pages of manuscript and anticipate slightly more than 600 in total. Not much progress happening currently as all the deferred house projects came due at the same time. Hope to get back to the book in a month or two.
Thanks for your continuing interest
-
08-08-2007, 11:14 PM #6
Oh no......Just seeing that bit of the book has me already salavating..... Wife better hide the check book!!!!
-
08-09-2007, 04:30 AM #7
Hi Mike and welcome to MyCockpit.org.
I have just made a dimmer circuit as described in your website and have successfully made dimmable wash lighting for the MIP, it looks and works great. My first foray into electronics!
Thank you for sharing the info,
Gwyn
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
Similar Threads
-
help ref wiring
By BishBash in forum I/O Interfacing and HardwareReplies: 26Last Post: 11-03-2010, 07:06 PM -
landing Gear wiring question.
By Air Canada in forum OpenCockpits General DiscussionReplies: 2Last Post: 06-27-2010, 11:57 PM -
wiring
By phil. in forum OpenCockpits General DiscussionReplies: 3Last Post: 09-15-2008, 03:38 AM -
Wiring
By imported_767300 in forum General Builder Questions All Aircraft TypesReplies: 10Last Post: 06-10-2007, 01:46 PM
Search Womans from your town for night
HDG preselect function