Results 1 to 8 of 8
  1. #1
    300+ Forum Addict jmig's Avatar
    Join Date
    Apr 2007
    Location
    Lafayette, LA USA
    Posts
    422
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Master Card: Is it working?

    OK gang. I finally got around to hooking up my master card. Well, let's say attempting to hook it up. As usual, nothing works as advertised. I kept getting a lot of spurious inputs in the blank box of the controller program.

    I am running through a USB adapter because, I don't have a parallel port on my computer. So, I moved everything to a different computer. The Master card checked out fine. It did what the tutorial says it should do.

    When connected to the USB port, back on the FSX computer the controller program shows the USB connection to be good. It shows one Master card and no inputs.

    However, when shorting the pins, I get a blink of the red LSD on the USB card but nothing shows up in the white input box. Yet, the counter go up one.

    I did find out that my problem is that cheap USB connector on the USB card. I can wiggle it until the LED stays on. When the master card is connected the LED goes out. It flashes when I short pins on the master card. I connected a pot to the A/D pins and I can see the value change as I twist the pot. Are these the correct behaviors?
    John

    System:
    ASUS P5Q SE/R
    Intel Q9550 O/C to 3.4 GHz
    4 GB 1066 DDR2 RAM
    300 GB WD 10,000 RPM Raptor SATA Drive
    GeForce 8800 GT 512 KB RAM
    Matrox TH2Go with three 19" Sumsung 940 BX
    IR Track 4

  2. #2
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,221
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hey John,

    I am not quite sure what to tell you.

    I know that I use to use a parallel controlled interface. From experience I know that it will only work on a genuine parallel port. It will not work on a parallel usb convertor.

    I would check on the forums for your interface card, I would be willing to bet that they will tell you the same thing. I am sure that is not good news where you are concerned, however, I would think that is 1/2 your battle. especially when you only got the problems when you moved to the usb converter.

    Trev
    ________________________
    Trevor Hale

  3. #3
    500+ This must be a daytime job kiek's Avatar
    Join Date
    Jan 2007
    Location
    Netherlands
    Posts
    698
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I'd recommend to use the USB expansion card from Opencockpits.

    Saves you lots of trouble.

    My 2 cts.

    Nico Kaan

  4. #4
    300+ Forum Addict jmig's Avatar
    Join Date
    Apr 2007
    Location
    Lafayette, LA USA
    Posts
    422
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by kiek View Post
    I'd recommend to use the USB expansion card from Opencockpits.

    Saves you lots of trouble.

    My 2 cts.

    Nico Kaan
    That is what I have. The USB expansion card. Sorry, if I misled anyone.
    John

    System:
    ASUS P5Q SE/R
    Intel Q9550 O/C to 3.4 GHz
    4 GB 1066 DDR2 RAM
    300 GB WD 10,000 RPM Raptor SATA Drive
    GeForce 8800 GT 512 KB RAM
    Matrox TH2Go with three 19" Sumsung 940 BX
    IR Track 4

  5. #5
    10+ Posting Member
    Join Date
    Feb 2008
    Location
    Canada
    Posts
    19
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by jmig View Post
    I kept getting a lot of spurious inputs in the blank box of the controller program.
    Spurious inputs is a sign that either the Mastercard is not recognized or there is insufficient power to the card. Are you using external power? (My cards needed external power.) Someone suggested measuring the voltage between the bottom-left and top-right pins of each IC for about 5 VDC. (And if you assembled your own card, then double-check the orientation of each IC.)

    Quote Originally Posted by jmig View Post
    However, when shorting the pins, I get a blink of the red LSD on the USB card but nothing shows up in the white input box. Yet, the counter go up one.... I can wiggle it until the LED stays on.
    The LED is not suppose to stay on. It is suppose to blink for each input.

    I don't recall seeing an input counter in controlador. The number (in red) to the right of "Inputs" is the most recent pin shorted while the box shows the last sequence of inputs but I'm not sure when the box is cleared.

    Are you seeing a USB Device number at the bottom? If not, double-check your controaldor.ini has both USB=Yes and Expansion=Yes. (On mine, USB port is always enabled and N.cards = 1 even when I have nothing connected so they are not good indicators.)

  6. #6
    300+ Forum Addict jmig's Avatar
    Join Date
    Apr 2007
    Location
    Lafayette, LA USA
    Posts
    422
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks to all who responded and provided possibilities. I now have it working.

    It was working. The cards are in front of sim (behind the monitors) By the time I would get around to see them, the input had disappeared. I finally wired up the canopy opening switch and could see it from within the cockpit.

    Now, if I could only get the programing to work...

    Oh well, another time, another night. One tiny step closer to the finish of the marathon.
    John

    System:
    ASUS P5Q SE/R
    Intel Q9550 O/C to 3.4 GHz
    4 GB 1066 DDR2 RAM
    300 GB WD 10,000 RPM Raptor SATA Drive
    GeForce 8800 GT 512 KB RAM
    Matrox TH2Go with three 19" Sumsung 940 BX
    IR Track 4

  7. #7
    1000+ Poster - Fantastic Contributor AndyT's Avatar
    Join Date
    Jun 2006
    Location
    Oahu, Hawaii
    Posts
    1,228
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I'd love to help out, but I have a VISA not MasterCard.

    (somedays I hurt myself being funny and the rest of the time its just sad....)
    God's in command, I'm just the Pilot.
    http://www.geocities.com/andytulenko/

  8. #8
    300+ Forum Addict jmig's Avatar
    Join Date
    Apr 2007
    Location
    Lafayette, LA USA
    Posts
    422
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by AndyT View Post
    I'd love to help out, but I have a VISA not MasterCard.

    (somedays I hurt myself being funny and the rest of the time its just sad....)


    I figure, you had better laugh at yourself.
    .
    .
    .
    Everyone else is laughing at you.
    John

    System:
    ASUS P5Q SE/R
    Intel Q9550 O/C to 3.4 GHz
    4 GB 1066 DDR2 RAM
    300 GB WD 10,000 RPM Raptor SATA Drive
    GeForce 8800 GT 512 KB RAM
    Matrox TH2Go with three 19" Sumsung 940 BX
    IR Track 4

Similar Threads

  1. Master card inoperative
    By 737NUT in forum OpenCockpits General Discussion
    Replies: 25
    Last Post: 04-15-2010, 10:43 PM
  2. IO Cards Problem setting up Display Card on Master Card
    By Barrykensett in forum OpenCockpits General Discussion
    Replies: 1
    Last Post: 05-02-2009, 01:30 PM
  3. Some help for Master card
    By cesarfsim in forum OpenCockpits General Discussion
    Replies: 9
    Last Post: 04-01-2008, 03:08 AM
  4. Build The Master Card
    By Gaspode in forum My Cockpit Update
    Replies: 6
    Last Post: 09-01-2007, 11:46 PM
  5. LED:s to master card
    By Jouni in forum I/O Interfacing Hardware and Software
    Replies: 1
    Last Post: 12-10-2006, 09:29 PM