Results 1 to 6 of 6
  1. #1
    1000+ Poster - Fantastic Contributor
    Join Date
    Nov 2008
    Location
    Europe
    Posts
    1,931
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Help on mechanism for flaps switch!

    Hi All,

    What is the best way to achieve the Cessna 172 flaps switch mechanism.

    I'm looking at building a simple 4 position flaps switch, using a rotary switch, simply by adding a lever to the switch and selecting whatever position is required (i.e UP, 10, 20, FULL).

    What rotary switch would be good for this mechanism? I am looking at this:

    http://cgi.ebay.co.uk/3-Pole-4-Posit...plies_ET?hash=

    If you look at the picture, there are an excessive amount of pins, how would you put this into perspective with the LeoBodnar board?

    Would this work or not? If not, what other type is there available for this sort of thing.

    Cheers!

    Alex

  2. #2
    500+ This must be a daytime job Jackpilot's Avatar
    Join Date
    Dec 2005
    Location
    MONTREAL
    Posts
    927
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Help on mechanism for flaps switch!

    The flaps lever on a 172 has a gate, so each position is well physically defined.

    You would be better off with a slider pot vertically mounted which axis you can calibrate with FSUIPC according to the position of the lever at each notch of the gate.
    Jackpilot
    B737-700 Posky
    FS9/P.Magenta
    without PMSystem

  3. Thanks No Longer Active, Geremy Britton thanked for this post
  4. #3
    25+ Posting Member
    Join Date
    Aug 2007
    Location
    SW Florida USA
    Posts
    72
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Help on mechanism for flaps switch!

    The potentiometer is a good idea. It is simple and would work great.

    If you still want to use the switch here is one way to do it.

    The switch has plenty of contacts and appears to have 30 degree detents (You should check this). The flap lever will then have 4 stops 30 degrees apart. These would be ready made detents.

    You only need 1 of the 4 switch sections so you can ignore all the rest of the contacts on the switch.

    Buy three 5K -1/2 W resistors from Radio Shack.

    Hook 1 switch wiper to one of the analog inputs of the Bu0836 card.
    Connect the resistor junctions to the switch poles as shown.
    Connect the resistors to the +5v and gnd terminals of the Bu0836 card.

    This will provide 4 voltage steps to the Bu0836 card analog input.
    You can then set FSUIPC to activate one increment of flaps with each voltage step.

    See picture attached

    Regards Ken K
    Attached Images Attached Images

  5. Thanks No Longer Active thanked for this post
  6. #4
    25+ Posting Member
    Join Date
    Sep 2008
    Location
    Belgium
    Posts
    57
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Help on mechanism for flaps switch!

    Hi Guys,

    I did one with a potentiometer which you can calibrated later on with FSUIPC on the steps you want. I added also 4 leds of different color to clearly indicate the flaps position.

    Renegade
    www.aileszelles.be
    Attached Images Attached Images

  7. Thanks No Longer Active thanked for this post
  8. #5
    300+ Forum Addict



    Join Date
    Jan 2009
    Location
    Tampa
    Posts
    487
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Help on mechanism for flaps switch!

    For physical detents I use a simple setup with a panel drilled with holes for each position of flaps/brakes/etc. Then I pivot a lever at the back and use an acorn nut aligned with the holes to hold it in place.


    BuddyM

  9. Thanks No Longer Active thanked for this post
  10. #6
    75+ Posting Member ddimm's Avatar
    Join Date
    Feb 2007
    Location
    Norcross
    Posts
    114
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Help on mechanism for flaps switch!

    You can also try using a radio shack toggle switch and hack and old joystick with leds already wired in. I used this for my C-172 sim project and calibrated the flap positions with FSUIPC. Most of the old Cessnas that I have flown just have a toggle switch for the flaps anyway.

    http://www.mycockpit.org/forums/show...ht=flap+switch

Similar Threads

  1. Flaps switch idea!
    By CessnaGuy in forum General Aviation (GA) Builder Disccusion
    Replies: 13
    Last Post: 07-06-2010, 11:05 AM
  2. Yoke mechanism progress
    By ivar hestnes in forum My Cockpit Update
    Replies: 9
    Last Post: 08-28-2008, 04:23 PM