Results 1 to 4 of 4
  1. #1
    New Member
    Join Date
    Apr 2007
    Location
    Chile
    Posts
    2
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Help for 767 throttle

    Hello ,

    I am just starting to build a 767 throttle. I would appreciate all kind of help, specially any draw of outside dimensions.

    Thank you and best regards
    CVAR

  2. #2
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Sorry, I don't have any dimensions, but for some general info; mine is build using the bulkhead method. Several (11 to be exact) bulkheads are cut for the various contours found at different points on the throttle housing.

    The bulkheads are joined by a common threaded rod with all levers pivoting on this rod. After ensuring everything is square, the bulkheads are screwed to a plywood base. There is a lot of stuff in a three engine Boeing throttle and not much space inside. A twin-engine throttle will increase you inside working room somewhat.

    Mine was cut from 1/2" MFD and a couple of bulkheads cut from 1/8" and is quite heavy. About 25 lbs. It is covered with aluminum, styrene plastic, and rubber sheeting.

    All of this is screwed down with over 30 stainless steel flat-head screws.

    See my photo gallery for a few shots in an exploded view and under construction.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  3. #3
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up

    Hi! You could maybe contact this dude . He may be able to help you.


    http://home.scarlet.be/wachters.erik/




    The seem to have lots of stuff here. http://www.airplanestuff.com/333.html




    Mike
    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

  4. #4
    New Member
    Join Date
    Apr 2007
    Location
    Chile
    Posts
    2
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thank you Mike and best regards

    CVAR

Similar Threads

  1. MD 80 throttle
    By verticallimit in forum My Cockpit Update
    Replies: 1
    Last Post: 09-03-2010, 03:07 AM
  2. MD-83 Throttle Quadrant, Boeing 737-300 Throttle Quadrant
    By Chaser in forum Off Site Articles For Sale
    Replies: 0
    Last Post: 04-05-2010, 07:10 PM
  3. 747 throttle
    By Jake 747 400 in forum General Builder Questions All Aircraft Types
    Replies: 8
    Last Post: 02-17-2009, 04:48 PM
  4. Throttle
    By Roger in forum General Builder Questions All Aircraft Types
    Replies: 11
    Last Post: 08-16-2008, 12:14 PM
  5. Throttle
    By cesarfsim in forum Where to Start Building a Home Cockpit
    Replies: 8
    Last Post: 06-23-2008, 11:20 PM