Results 1 to 3 of 3
  1. 01-06-2011, 04:44 AM #1
    NCW
    NCW is offline
    25+ Posting Member NCW's Avatar
    Join Date
    Jun 2008
    Location
    Woomelang, Victoria
    Posts
    32
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Rocker switches/LED wiring

    Hi,
    I have 2 rocker switches, each with 6 terminals on the back. I want to use them as generator on/off switches, connected through a BU0836 card and FSUIPC. I also have 2 LED's connected to each, to indicate run or off. I have attempted to utilise the 5v supply from an ATX PSU. for the LED power supply. I think that I have damaged the card somehow, by incorrectly wiring the switches, so that the 5v was put throught the card by mistake. There are only 2 buttons permanently lit, and the rest seem okay, however, thats my problem, and I can live with it.
    My question is, can someone please advise me on the correct way to wire it all up, so that I dont do anymore damage.
    Cheers,

    Neil
    Reply With Quote Reply With Quote
  2. 01-06-2011, 06:04 PM #2
    verticallimit
    verticallimit is offline
    150+ Forum Groupie
    Tutorial Contributor / Point Value: 10 Tutorial Contributor / Point Value: 10
    Total Awards: 2
    Total Points: 20
    verticallimit's Avatar
    Join Date
    Apr 2009
    Location
    Denmark, Sinding
    Posts
    212
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rocker switches/LED wiring

    Hi Neil

    Firstly, mount the power supply and LEDs without your the bu card connected.
    Then you'll try if you can get the LEDs to change to light when the switch is rocked.
    If this works you can then mount your bu card.

    80% of all contacts are made with the common pin in the middle.
    Sincerely,

    Claus

    Reply With Quote Reply With Quote
  3. 01-09-2011, 05:29 AM #3
    NCW
    NCW is offline
    25+ Posting Member NCW's Avatar
    Join Date
    Jun 2008
    Location
    Woomelang, Victoria
    Posts
    32
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Rocker switches/LED wiring

    Hi Claus,
    Thanks for reply, and your clear and understandable drawing. Did as you suggested, and everything works well.
    Regards,

    Neil
    Reply With Quote Reply With Quote
  4. Post Thanks / Like - 2 Thanks, 0 Likes, 0 Dislikes
    Thanks Buckster13, verticallimit thanked for this post
« Previous Thread | Next Thread »

Similar Threads

  1. Rocker switch & LED wiring
    By NCW in forum Westozy's Mechanical Engineering
    Replies: 3
    Last Post: 10-08-2010, 05:15 AM
  2. Rocker Switches
    By justinm001 in forum General Aviation (GA) Builder Disccusion
    Replies: 9
    Last Post: 04-18-2010, 09:51 AM
  3. Wiring Switches, Pots, Slides
    By AndyT in forum I/O Interfacing Hardware and Software
    Replies: 1
    Last Post: 11-03-2008, 10:31 AM
  4. Toggle switches to momentary switches?
    By Patrik in forum Where to Start Building a Home Cockpit
    Replies: 5
    Last Post: 10-23-2007, 09:58 AM