Page 1 of 5 12345 LastLast
Results 1 to 10 of 48
  1. #1
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up gear up gear down

    +Back 3 years ago I suffered a serious head injury. I have problems remembering things. So, if you see me asking the same questions over and over this could be problem. Thanks for understanding

    This site with all of you and my project has fired me up. My wife says she hasn't seen me so excited about something since the accident. So, you will see a lot of questions from me. PICS TO COME VERY VERY SOON.


    Could someone please tell me what and where to get the switches that I need for ex: Gear up gear down. When I move the handle it contacts the switch.

    The flying trucker Mike
    Last edited by Radar; 04-03-2007 at 10:49 AM. Reason: mispelled
    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

  2. #2
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi Mike. Do not worry about the questions that is what we built this site for! I need a little more info to help you. What interface are you using to connect your switches to the computer?
    Bob Reed

  3. #3
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I think I will take Westozys suggestion and get Simboards Master module, and a 64x8x8 input module .
    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

  4. #4
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    That sounds like a really good idea. Ok.. What sim are you going to build? And what are you going to use for your gear lever? A simple on off toggle switch can run your gear. So I need a little more info...
    Bob Reed

  5. #5
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Bob Reed View Post
    That sounds like a really good idea. Ok.. What sim are you going to build? And what are you going to use for your gear lever? A simple on off toggle switch can run your gear. So I need a little more info...
    Ok! Thanks Bob.
    I'm building a 737NG. I got the MIP stand,Mip,MFC glaresheild,FMC box and the pedestal box done.

    I would like to do something simple for my gear lever. Any suggestions

    Thanks Mike
    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

  6. #6
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    If my blasted camera ever gets back I will take a picture of what I did with mine. Right now I am just using a toggle switch to lower and raise the gear. Pics soon I hope!
    Bob Reed

  7. #7
    300+ Forum Addict Rodney's Avatar
    Join Date
    Nov 2005
    Location
    Colorado Springs, CO USA
    Posts
    331
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Radar,
    take a look at this builders idea.
    http://babelfish.altavista.com/babel...in%2ftrain.htm
    Rodney -
    Real 727-200 pit
    Last Flown as N392PA
    FS9

  8. #8
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi Mike,

    Here's a pic of my gear lever mechanism using micro switches, they are pretty cheap. This simple design gives a really solid feel with the lever clicking into any of the three positions.

    http://www.mycockpit.org/photopost/s....php?photo=590

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  9. #9
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Mike, those are also called snap action, or just snap switches. I've used them in several places in my equipment.

    They are easier to use and adjust if you buy them with a lever attached. They come in various sizes and lever lengths. You can also get them with a wire lever or a roller lever for a very smooth movement.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  10. #10
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up

    Wonderful.
    Lots of great ideas for me to look at. Thanks eveybody

    Boeing Skunk Works. I looked at the Mousers page and saw snap switches. But I don't know what kind I would need.
    How many would you estimate that I would need for a 737NG simpit.
    Last edited by Radar; 04-03-2007 at 09:00 PM. Reason: added more comments
    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

Page 1 of 5 12345 LastLast

Similar Threads

  1. Gear LED's
    By Clive in forum I/O Interfacing and Hardware
    Replies: 5
    Last Post: 04-09-2011, 02:38 AM
  2. Gear pictures
    By mondo50m in forum CNC Discussion
    Replies: 4
    Last Post: 12-04-2010, 10:45 AM
  3. Gear switch
    By flatlandpilot in forum Westozy's Mechanical Engineering
    Replies: 7
    Last Post: 05-01-2010, 08:54 PM
  4. CNC Gear Machining
    By Westozy in forum Westozy's Mechanical Engineering
    Replies: 6
    Last Post: 12-06-2009, 04:32 AM