Some problems with OC servo flaps gauge

[dimon2kgb]

Hi all!

Yesterday got the Flaps Indicator.

But there is one issue. I've programmed my sioc ( scroll down
my post ), the synchronization is OK (for example, Flaps 5 in my FSX is
Flap 5 on my Servo indicator). BUT! The pointer is shaking while moving.
It's not smoothly, as it should be. I think it is so, because the pointer on
the real servo gauge moves faster, than the simulator's one. So, when it
indicate, for example 5degrees, the simulator gauge shows the middle of 2
and 5 degrees. So the pointer "wants" to go back, to the middle, but in the
sim it's already on 5degrees. So, it starts reeling from side to side. What
do you think about it?


And, of course, my SIOC:

Var 0606, name LE_EXT_LED, link IOCARD_OUT, output 95
Var 0608, name LE_TRANS_LED, link IOCARD_OUT, output 96
Var 0612, name FLAPS_IN, Link FSUIPC_IN, Offset $0BE0, Length 4
{
L0 = &FLAPS_IN
L0 = ABS L0

IF L0 = 0
{
&LE_EXT_LED = 0
&LE_TRANS_LED = 0
}
ELSE
{
L1 = 0
&LE_TRANS_LED = 1
IF L0 = 409
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 819
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 2047
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 4095
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 6143
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 10239
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 12287
{
L1 = 1
&LE_TRANS_LED = 0
}
IF L0 = 16383
{
L1 = 1
&LE_TRANS_LED = 0
}
&LE_EXT_LED = L1
}

L2 = L0

C0 = L0 >= 0
C1 = L0 <= 409
IF C0 AND C1
{
// x1,x2 = FSUIPC positions, y1,y2 = Real servo-motor positions
&x1 = 0 // between 0 and 1
&x2 = 409
&y1 = 1023
&y2 = 927
}


C0 = L0 >= 409
C1 = L0 <= 819
IF C0 AND C1
{
&x1 = 409
&x2 = 819
&y1 = 927
&y2 = 795 // between 1 and 2
}
C0 = L0 >= 819
C1 = L0 <= 2047
IF C0 AND C1
{
&x1 = 819
&x2 = 2047
&y1 = 795
&y2 = 674 // between 2 and 5
}
C0 = L0 >= 2047
C1 = L0 <= 4095
IF C0 AND C1
{
&x1 = 2047
&x2 = 4095
&y1 = 674
&y2 = 532 // between 5 and 10
}
C0 = L0 >= 4095
C1 = L0 <= 6143
IF C0 AND C1
{
&x1 = 4095
&x2 = 6143
&y1 = 532
&y2 = 430 // between 10 and 15
}
C0 = L0 >= 6143
C1 = L0 <= 10239
IF C0 AND C1
{
&x1 = 6143
&x2 = 10239
&y1 = 430
&y2 = 339 // between 15 and 25
}
C0 = L0 >= 10239
C1 = L0 <= 12287
IF C0 AND C1
{
&x1 = 10239
&x2 = 12287
&y1 = 339
&y2 = 248 // between 25 and 30
}
C0 = L0 >= 12287
C1 = L0 <= 16383
IF C0 AND C1
{
&x1 = 12287
&x2 = 16383
&y1 = 248
&y2 = 177 // between 30 and 40
}
&dy21 = &y2 - &y1
&dx21 = &x2 - &x1
&dx = L0 - &x1
&dy = &dy21 * &dx
&dy = &dy / &dx21
L1 = &y1 + &dy
&FLAPSERVO = L1
}

Var 0610, name FLAPSERVO, Link USB_SERVOS, device 3, Output 1, PosL 0, PosC 511, PosR 1023

Var 0614, name dy
Var 0616, name dx21
Var 0618, name dy21
Var 0620, name dx
Var 0622, name x1
Var 0624, name x2
Var 0626, name y1
Var 0628, name y2

[dimon2kgb]

http://www.youtube.com/watch?v=MQEi-hcVCx4 - Video!