Results 1 to 2 of 2
  1. 06-24-2010, 04:06 AM #1
    Per Alm
    Per Alm is offline
    75+ Posting Member
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100
    Per Alm's Avatar
    Join Date
    Jan 2008
    Location
    Sweden
    Posts
    140
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question Controlling client functions through server computer input!??

    I recently bought the fantastic BU0836A Ultra precision joystick controller from Leo Bodnar. It's connected to the server computer to control a few different functions in my pit.
    However I also need to separately control some functions on my Clients:
    1. Capt PFD/ND (PMRJ)
    2. FO PFD/ND (PMRJ)
    Today I use slaughtered keyboards to control different modes i the ND display like VOR, NDB etc. Due to instability of theese slughtered keyboards I need to use something else to interface.

    Is it possible to do this through the server computer or do I need some separate interfacing device for each client? If so what would you suggest. Are there any, not too expensive keyboard emulators out there I can use?

    Regards / Per Alm
    www.learsim.se
    Reply With Quote Reply With Quote
  2. 06-24-2010, 04:26 AM #2
    ian@737ng.co.uk
    ian@737ng.co.uk is offline
    500+ This must be a daytime job
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100
    ian@737ng.co.uk's Avatar
    Join Date
    Jan 2006
    Location
    Oswestry, Shropshire
    Posts
    604
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Controlling client functions through server computer input!??

    hello per........
    i have used these in the past and once you get your head round connecting them up,
    they work very well.........
    http://www.opencockpits.com/catalog/...ml?cPath=21_35
    have a look at this document which will help you understand how these work.
    http://www.737ng.co.uk/USBKeys.pdf
    hope that helps you out captain.....
    regards from wales ... ian
    Mr. Ian. P. Sissons is hereby recognised as an Honorary Flight Sim Captain following his passing in February 2016. This is in recognition for his commitment to Flight Simulation.

    www.mycockpit.org Featured Builder August 2008 www.737ng.co.uk
    FS9/PROSIM737/CPFLIGHT/Lots of BU0836X's and a Beer Fridge
    Reply With Quote Reply With Quote
  3. Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
    Thanks Per Alm thanked for this post
« Previous Thread | Next Thread »

Similar Threads

  1. Question about controlling clients through server computer via FSUIPC and WideFS
    By Per Alm in forum General Builder Questions All Aircraft Types
    Replies: 0
    Last Post: 06-24-2010, 03:04 AM
  2. Controlling Instruments on Second Computer
    By colt45 in forum General Builder Questions All Aircraft Types
    Replies: 9
    Last Post: 02-25-2010, 06:41 PM
  3. Change server to Client?l
    By props in forum Computer Hardware Setup
    Replies: 3
    Last Post: 09-11-2009, 11:14 PM
  4. Controlling the monitors behind the MIP
    By vidarf in forum General Builder Questions All Aircraft Types
    Replies: 12
    Last Post: 06-03-2008, 02:31 PM
  5. Controlling the sim network via 1 PC
    By Tomlin in forum Computer Hardware Setup
    Replies: 2
    Last Post: 08-29-2007, 07:10 PM